Singer 9980 QUANTUM STYLIST Instruction Manual - Page 34

D.threading The Needle Eye, Drawing Up The Bobbin Thread, Caution: To Prevent Accidents.

Get Singer 9980 QUANTUM STYLIST PDF manuals and user guides View all Singer 9980 QUANTUM STYLIST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

D. THREADING THE NEEDLE EYE CAUTION: To prevent accidents. 1. Keep fingers away from all moving parts. Special care is required around the needle. 2. Do not lower the threader lever while machine is operating. Note:The needle threader is used for needle sizes 11/80, 14/90, and 16/100. 1. Lower the presser foot. 2. Check that the needle is raised. If it is not so, raise needle by pressing needle up/down button. 3. Lower the threader slowly and draw thread through thread guide (a) and pull toward the right. 4. Lower the lever as far as it will go. The threader will turn and the hook pin will go through the needle eye. 5. Draw thread into the guide. 6. Hold thread loosely and release the lever. Hook will turn and pass thread through needle eye while making a loop. 7. Pull thread out about 10 cm (4 inches) through the needle eye. DRAWING UP THE BOBBIN THREAD This machine can start to sew without drawing up the bobbin thread. If you want to start sewing with longer bobbin thread, draw up the bobbin thread as follows. 1. Insert the bobbin into the bobbin holder and pass thread as page 30. But do not cut the thread. 2. Raise the presser foot. 3. Hold thread loosely and press needle up-down button twice from up position. The hand wheel will turn one complete turn. 4. Pull upper thread lightly. Bobbin thread will come up in a loop. 5. Pull both upper and bobbin threads about 10 cm toward the back of presser foot. 6. Replace the bobbin cover. (See page 30) 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
34
D.THREADING THE NEEDLE EYE
DRAWING UP THE BOBBIN THREAD
This machine can start to sew without drawing up
the bobbin thread.
If you want to start sewing with longer bobbin
thread, draw up the bobbin thread as follows.
1.
Insert the bobbin into the bobbin holder and
pass thread as page 30. But do not cut the
thread.
2.
Raise the presser foot.
3.
Hold thread loosely and press needle up-down
button twice from up position.
The hand wheel will turn one complete turn.
4.
Pull upper thread lightly. Bobbin thread will
come up in a loop.
5.
Pull both upper and bobbin threads about 10
cm toward the back of presser foot.
6.
Replace the bobbin cover. (See page 30)
CAUTION: To prevent accidents.
1.
Keep fingers away from all moving parts.
Special care is required around the needle.
2.
Do not lower the threader lever while machine
is operating.
Note:The needle threader is used for needle sizes
11/80, 14/90, and 16/100.
1.
Lower the presser foot.
2.
Check that the needle is raised.
If it is not so, raise needle by pressing needle
up/down button.
3.
Lower the threader slowly and draw thread
through thread guide (a) and pull toward the
right.
4.
Lower the lever as far as it will go. The threader
will turn and the hook pin will go through the
needle eye.
5.
Draw thread into the guide.
6.
Hold thread loosely and release the lever.
Hook will turn and pass thread through needle
eye while making a loop.
7.
Pull thread out about 10 cm (4 inches) through
the needle eye.