Sony DAV-DX255 Operating Instructions - Page 17

Connecting the AC power cord (mains lead), Changing the color system (PAL or NTSC) - speaker connection wires

Page 17 highlights

Getting Started - BASIC - To connect the FM wire antenna (aerial) Connect the FM wire antenna (aerial) to the COAXIAL FM 75 Ω jack. FM wire antenna (aerial) (supplied) FM wire antenna (aerial) (supplied) or COAXIAL FM 75 Ω jack COAXIAL FM 75 Ω jack Note • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip • If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the system to an outdoor FM antenna (aerial) as shown below. System Outdoor FM antenna (aerial) 4 Connecting the AC power cord (mains lead) Before connecting the AC power cord (mains lead) of this system to a wall outlet (mains), connect the speakers to the system. Install this system so that the power cord can be unplugged from the wall socket immediately in the event of trouble. Changing the color system (PAL or NTSC) (Asian, Australian, and Middle Eastern models only) Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color system. The initial setting of the system for Australian and Middle Eastern models is PAL. The initial setting of the system for Asian models is NTSC. To change the color system 1 Turn off the system by pressing "/1. 2 Turn on the system by pressing "/1 while pressing X on the system. You need to hold X until the set powers on. Each time you perform this operation, the color system toggles between PAL and NTSC. "NTSC" lights up in the front display when the color system is set to NTSC. 17GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100

17
GB
Getting Started – BASIC –
To connect the FM wire antenna (aerial)
Connect the FM wire antenna (aerial) to the COAXIAL FM 75
jack.
Note
• Be sure to fully extend the FM wire antenna (aerial).
• After connecting the FM wire antenna (aerial), keep it as horizontal as possible.
Tip
• If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the system to an outdoor FM
antenna (aerial) as shown below.
4
Connecting the AC power cord (mains lead)
Before connecting the AC power cord (mains lead) of this system to a wall outlet (mains), connect the
speakers to the system.
Install this system so that the power cord can be unplugged from the wall socket immediately in the
event of trouble.
Changing the color system (PAL or NTSC)
(Asian, Australian, and Middle Eastern models only)
Depending on the TV to be connected, you may be required to select either PAL or NTSC for the color
system.
The initial setting of the system for Australian and Middle Eastern models is PAL.
The initial setting of the system for Asian models is NTSC.
To change the color system
1
Turn off the system by pressing
"
/
1
.
2
Turn on the system by pressing
"
/
1
while pressing
X
on the system.
You need to hold
X
until the set powers on.
Each time you perform this operation, the color system toggles between PAL and NTSC.
“NTSC” lights up in the front display when the color system is set to NTSC.
FM wire antenna (aerial)
(supplied)
COAXIAL FM 75
jack
FM wire antenna (aerial)
(supplied)
COAXIAL FM 75
jack
or
Outdoor FM antenna (aerial)
System