Sony VPL-FX30 Operating Instructions - Page 21

The Connection/Power Menu

Get Sony VPL-FX30 PDF manuals and user guides View all Sony VPL-FX30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

The Connection/Power Menu The Connection/Power menu is used for setting for the connections and power. Setting items Description Network Setting IP Address Setup Auto (DHCP): The IP address is assigned automatically from the DHCP server such as a router. Manual: To specify the IP Address manually. IP Address/ Subnet Mask/ Default Gateway/Primary DNS/Secondary DNS When "Manual" is selected for "IP Address Setup," select the item with the B or b key and input the value with V or v key. When all items are entered, select "Apply" then press the ENTER key. The entered settings will be registered. Input-A Signal Sel. Auto/Computer/Video GBR/Component: When set to "Auto," selects the type of video signal input automatically when "Input-A" is selected with the INPUT key.*1 Color System Standby Mode*2 Auto/NTSC3.58/PAL/SECAM/NTSC4.43/PAL-M/PAL-N: When set to "Auto," selects the color system automatically when "S Video" or "Video" is selected with the INPUT key.*1 Standard/Low: When set to "Low," lowers power consumption in Standby mode. Power Saving Mode Lamp Cutoff: The lamp turns off automatically and power consumption is reduced if no signal is input for 10 minutes. The lamp lights again when a signal is input or any key is pressed. In Lamp Cutoff, the ON/STANDBY indicator lights in orange (page 27). Standby: The power will be turned off automatically and the projector goes to Standby mode if no signal is input for 10 minutes. Off: The Power Saving Mode is released. Direct Power On On/Off: When set to "On," you can turn the power on without going to Standby mode when the AC power cord is connected to a wall outlet. You can also unplug the AC power cord without going to Standby mode when you turn off the projector. You may unplug the AC power cord without going to Standby mode. Notes *1: The image may not be adjusted properly depending on the type of input signal. In such a case, adjust it manually to suit to the connected equipment. *2: When "Standby Mode" is set to "Low," the network and network control function cannot be operated while the projector is in standby mode. Adjustments and Settings Using a Menu The Connection/Power Menu 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
21
The Connection/Power Menu
Adjustments and Settings Using a Menu
The Connection/Power Menu
The Connection/Power menu is used for setting for the connections and power.
*1:
The image may not be adjusted properly depending on the type of input signal. In such a case,
adjust it manually to suit to the connected equipment.
*2:
When “Standby Mode” is set to “Low,” the network and network control function cannot be
operated while the projector is in standby mode.
Setting items
Description
Network Setting
IP Address Setup
Auto (DHCP):
The IP address is assigned automatically from the
DHCP server such as a router.
Manual:
To specify the IP Address manually.
IP Address/ Subnet
Mask/ Default
Gateway/Primary
DNS/Secondary
DNS
When “Manual” is selected for “IP Address Setup,” select the item
with the
B
or
b
key and input the value with
V
or
v
key. When all
items are entered, select “Apply” then press the ENTER key. The
entered settings will be registered.
Input-A Signal Sel.
Auto/Computer/Video GBR/Component:
When set to “Auto,”
selects the type of video signal input automatically when “Input-A”
is
selected with the INPUT key.
*1
Color System
Auto/NTSC
3.58
/PAL/SECAM/NTSC
4.43
/PAL-M/PAL-N:
When set
to “Auto,” selects the color system automatically when “S Video” or
“Video” is selected with the INPUT key.
*1
Standby Mode
*2
Standard/Low:
When set to “Low,” lowers power consumption in
Standby mode.
Power Saving Mode
Lamp Cutoff:
The lamp turns off automatically and power
consumption is reduced if no signal is input for 10 minutes. The lamp
lights again when a signal is input or any key is pressed. In Lamp
Cutoff, the ON/STANDBY indicator lights in orange (page 27).
Standby:
The power will be turned off automatically and the projector
goes to Standby mode if no signal is input for 10 minutes.
Off:
The Power Saving Mode is released.
Direct Power On
On/Off:
When set to “On,” you can turn the power on without going
to Standby mode when the AC power cord is connected to a wall
outlet. You can also unplug the AC power cord without going to
Standby mode when you turn off the projector.
You may unplug the AC power cord without going to Standby mode.
Notes