Sony VPL-FX30 Operating Instructions - Page 28

Messages List

Get Sony VPL-FX30 PDF manuals and user guides View all Sony VPL-FX30 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Messages List When any of the messages listed below appears on the projected image, address the problem in accordance with the table below. Message Meaning/Remedy Page High temp.! Lamp off in 1 min. Check the items below. • Check to see if nothing is blocking the ventilation holes. • Check to see if the air filter is not clogged. • Check if "Installation Attitude" on the Installation menu is correctly selected. 3, 22, 33 Frequency is out of range! Change the output setting of the connected equipment to one 40 for signals supported by the projector. Please check Input-A Set "Input-A Signal Sel." to "Auto" or select the input signal 21 Signal Sel. type to suit to the input signal. Please replace the Lamp and clean the Filter. Replace the lamp with a new one and clean the air filter. To cancel the message, press any key on the Remote Commander or the control panel of the projector. The message appears whenever you turn on the power until you replace the lamp and reset the lamp timer. 31, 33 Projector temperature is high. High Altitude Mode should be "On" if the projector is being used at high altitude. At an altitude of 1,500 m or higher, if you are not using the projector, check the items below. • Check that nothing is blocking the ventilation holes. • Check that the air filter is not clogged. • Check if "Installation Attitude" on the Installation menu is correctly selected. 3, 22, 33 Not applicable! Invalid key pressed. 5 The panel keys are "Panel Key Lock" is set to "On." 20 locked! 28 Messages List

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
28
Messages List
Messages List
When any of the messages listed below appears on the projected image, address the problem in
accordance with the table below.
Message
Meaning/Remedy
Page
High temp.! Lamp off in
1 min.
Check the items below.
• Check to see if nothing is blocking the ventilation holes.
• Check to see if the air filter is not clogged.
• Check if “Installation Attitude” on the Installation menu is
correctly selected.
3, 22,
33
Frequency is out of
range!
Change the output setting of the connected equipment to one
for signals supported by the projector.
40
Please check Input-A
Signal Sel.
Set “Input-A Signal Sel.” to “Auto” or select the input signal
type to suit to the input signal.
21
Please replace the Lamp
and clean the Filter.
Replace the lamp with a new one and clean the air filter. To
cancel the message, press any key on the Remote Commander
or the control panel of the projector. The message appears
whenever you turn on the power until you replace the lamp and
reset the lamp timer.
31, 33
Projector temperature is
high. High Altitude
Mode should be “On” if
the projector is being
used at high altitude.
At an altitude of 1,500 m or higher, if you are not using the
projector, check the items below.
• Check that nothing is blocking the ventilation holes.
• Check that the air filter is not clogged.
• Check if “Installation Attitude” on the Installation menu is
correctly selected.
3, 22,
33
Not applicable!
Invalid key pressed.
5
The panel keys are
locked!
“Panel Key Lock” is set to “On.”
20