Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SG3109 » Manual Viewer

TP-Link TL-SG3109 User Guide - Page 23

Site Requirements, 3.1.3 Unpacking, 3.1.3.1 Package Contents

UPC - 845973020484

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

TL-SG3109/TL-SL3428/TL-SL3452 Gigabit Managed Switch Family Installation Guide Cautions  Ensure the air flow around the front, sides, and back of the switch is not restricted.  Ensure the cooling vents are not blocked.  Do not install the switch in an environment where the operating ambient temperature might exceed 40ºC (104ºF). 3.1.2 Site Requirements The device is placed on a table-top. Before installing the unit, verify that the location chosen for installation meets the following site requirements.  General - Ensure that the power supply is correctly installed.  Power - The unit is installed within 1.5 m (5 feet) of a grounded, easily accessible outlet 100-240 VAC, 50-60 Hz.  Clearance - There is adequate frontal clearance for operator access. Allow clearance for cabling, power connections and ventilation.  Cabling - The cabling is routed to avoid sources of electrical noise such as radio transmitters, broadcast amplifiers, power lines and fluorescent lighting fixtures.  Ambient Requirements - The ambient unit operating temperature range is 0 to 40ºC (32 to 104ºF) at a relative humidity of up to 95%, noncondensing. Verify that water or moisture cannot enter the device casing. 3.1.3 Unpacking 3.1.3.1 Package Contents While unpacking Cedar device, ensure that the following items are included:  The device  An AC power cable 16

Section	Page
Package contents	8
Section 1: Introduction	9
1.1 Intended Audience	9
1.2 Agreement	9
1.3 Guide Overview	9
Section 2. Device Description	10
2.1 Features	10
2.2 TP-Link TL-SG3109 Description	11
2.3 TP-Link TL-SL3428 Description	13
2.4 TP-Link TL-SL3452 Description	15
2.5 Back Panel	17
2.6 Device Hardware Interfaces	17
2.6.1 RJ-45 Base-T Fast Ethernet Ports	17
2.6.2 SFP Port	18
2.6.3 RS-232 DB-9 Console Port	19
2.7 Cable, Port, and Pinout Information	19
2.7.1 Pin Explain For RJ-45 Connector	19
2.7.2 SFP Connector	21
2.8 Physical Dimensions	21
Section 3. Mounting Device	22
3.1 Preparing for Installation	22
3.1.1 Installation Precautions	22
3.1.2 Site Requirements	23
3.1.3 Unpacking	23
3.1.3.1 Package Contents	23
3.1.3.2 Unpacking Essentials	24
3.2 Installing the Device	24
3.2.1 Desktop or Shelf Installation	25
3.2.2 Rack Installation	25
3.3 Connecting the Device	27
3.3.1 Connecting the Switch to a Terminal	27
3.3.2 AC Power Connection	28
Section 4. Starting and Configuring the Device	29
4.1 Configuring the Terminal	29
4.2 Installation Procedure	30
4.2.1 Device Port Default Settings	31
4.3 Booting the Device	31
4.4 Configuration Overview	33
4.4.1 Initial Configuration	34
4.4.1.1 Static IP Address and Subnet Mask	35
4.4.1.2 Assigning Static IP Addresses on a default VLAN	36
4.4.1.3 User Name	37
4.4.1.4 SNMP Community Strings	38
4.5 Advanced Configuration	40
4.5.1 Receiving an IP Address from a DHCP Server	41
4.5.2 Receiving an IP Address from a BOOTP Server	42
4.5.3 Security Management and Password Configuration	43
4.5.3.1 Configuring Security Passwords Introduction	44
4.5.3.2 Configuring an Initial Console Password	44
4.5.3.3 Configuring an Initial Telnet Password	45
4.5.3.4 Configuring an Initial SSH password	45
4.5.3.5 Configuring an Initial HTTP Password	46
4.5.3.6 Configuring an initial HTTPS Password	46
4.6 Startup Procedures	46
4.6.1 Software Download [Option 1]	48
4.6.1.1 Software Download through TFTP Server	49
4.6.2 Erasing the Flash File [Option 2]	53
4.6.3 Password Recovery [Option 3]	53
4.6.4 Enter Diagnostic Mode [Option4]	54