Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SG3109 » Manual Viewer

TP-Link TL-SG3109 User Guide - Page 37

User Name, Verifying the IP and Default Gateway Addresses

UPC - 845973020484

Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

TL-SG3109/TL-SL3428/TL-SL3452 Gigabit Managed Switch Family Installation Guide Verifying the IP and Default Gateway Addresses Ensure that the IP address and the default gateway were properly assigned by executing the following command and examining its output: Gateway IP Address Activity status ---- --- 192.168.1.1 Active IP address 192.168.1.123/24 Interface VLAN 1 Type -------Static 4.4.1.3 User Name A user name is used to manage the device remotely, for example through SSH, Telnet, or the Web interface. To gain complete administrative (super-user) control over the device, the highest privilege (15) must be specified. Note Only the administrator (super-user) with the highest privilege level (15) is allowed to manage the device through the Web browser interface. For more information about the privilege level, see the CLI Reference Guide. The configured user name is entered as a login name for remote management sessions. To configure user name and privilege level, enter the command at the system prompt as shown in the configuration example: console> enable console# configure console(config)# username admin password admin level 15 30

Section	Page
Package contents	8
Section 1: Introduction	9
1.1 Intended Audience	9
1.2 Agreement	9
1.3 Guide Overview	9
Section 2. Device Description	10
2.1 Features	10
2.2 TP-Link TL-SG3109 Description	11
2.3 TP-Link TL-SL3428 Description	13
2.4 TP-Link TL-SL3452 Description	15
2.5 Back Panel	17
2.6 Device Hardware Interfaces	17
2.6.1 RJ-45 Base-T Fast Ethernet Ports	17
2.6.2 SFP Port	18
2.6.3 RS-232 DB-9 Console Port	19
2.7 Cable, Port, and Pinout Information	19
2.7.1 Pin Explain For RJ-45 Connector	19
2.7.2 SFP Connector	21
2.8 Physical Dimensions	21
Section 3. Mounting Device	22
3.1 Preparing for Installation	22
3.1.1 Installation Precautions	22
3.1.2 Site Requirements	23
3.1.3 Unpacking	23
3.1.3.1 Package Contents	23
3.1.3.2 Unpacking Essentials	24
3.2 Installing the Device	24
3.2.1 Desktop or Shelf Installation	25
3.2.2 Rack Installation	25
3.3 Connecting the Device	27
3.3.1 Connecting the Switch to a Terminal	27
3.3.2 AC Power Connection	28
Section 4. Starting and Configuring the Device	29
4.1 Configuring the Terminal	29
4.2 Installation Procedure	30
4.2.1 Device Port Default Settings	31
4.3 Booting the Device	31
4.4 Configuration Overview	33
4.4.1 Initial Configuration	34
4.4.1.1 Static IP Address and Subnet Mask	35
4.4.1.2 Assigning Static IP Addresses on a default VLAN	36
4.4.1.3 User Name	37
4.4.1.4 SNMP Community Strings	38
4.5 Advanced Configuration	40
4.5.1 Receiving an IP Address from a DHCP Server	41
4.5.2 Receiving an IP Address from a BOOTP Server	42
4.5.3 Security Management and Password Configuration	43
4.5.3.1 Configuring Security Passwords Introduction	44
4.5.3.2 Configuring an Initial Console Password	44
4.5.3.3 Configuring an Initial Telnet Password	45
4.5.3.4 Configuring an Initial SSH password	45
4.5.3.5 Configuring an Initial HTTP Password	46
4.5.3.6 Configuring an initial HTTPS Password	46
4.6 Startup Procedures	46
4.6.1 Software Download [Option 1]	48
4.6.1.1 Software Download through TFTP Server	49
4.6.2 Erasing the Flash File [Option 2]	53
4.6.3 Password Recovery [Option 3]	53
4.6.4 Enter Diagnostic Mode [Option4]	54