URC URC-WR7 Owners Manual - Page 11

Three-Digit Set-up - manual

Get URC URC-WR7 PDF manuals and user guides View all URC URC-WR7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

2. Three-Digit Set-up STEP 1: Find the 3-digit code numbers for your component type and brand from the lists in the back of this manual. The codes are listed by component type (TV, VCR, DVD, etc.), then by brand name. Be sure to identify the list of codes for the correct component and brand. For instance, if you would have a Sony television, first locate the TV category, and then look for the Sony brand. Be careful. Codes for Sony DVDs may be different than from Sony TVs. You may want to write the numbers down on a piece of paper before moving to step two. STEP 2: Turn on the component you want to activate. (Other components can be on or off, it doesn't matter.) STEP 3: On your WR7 universal remote, press the Component button that you want to set up and the SELECT [SEL] button at the same time. Hold down both buttons for two seconds until the Component light turns on. This signals that you are in set-up mode, and you can then release the buttons. COMPONENT BUTTONS SELECT BUTTON STEP 4: Point the WR7 toward the component and use the number buttons 0-9 to punch in the first 3-digit code for that specific component. If the 3-digit code number you just punched in is the correct number, the component you are activating will turn off. If it did not turn off, enter the next code number from your list until it does turn off. Note: If you do not press a button within 30 seconds, the component light will turn off. The remote will exit the set-up mode, and you will have to start over with step three. Page | 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
Page | 10
2. Three-Digit Set-up
STEP 1:
Find the 3-digit code numbers for
your component type and brand from the
lists in the back of this manual. The codes
are listed by component type (TV, VCR, DVD,
etc.), then by brand name.
Be sure to
identify the list of codes for the correct
component and brand.
For instance, if you
would have a Sony television, first locate the
TV category, and then look for the Sony brand.
Be careful. Codes for Sony DVDs may be
different than from Sony TVs.
You may want to write the numbers down on
a piece of paper before moving to step two.
STEP 2:
Turn on the component you want to
activate. (Other components can be on or
off, it doesn’t matter.)
STEP 3:
On your WR7 universal remote,
press the Component button that you want to
set up and the SELECT [SEL] button at the
same time. Hold down both buttons for two
seconds until the Component light turns on.
This signals that you are in set-up mode, and
you can then release the buttons.
STEP 4:
Point the WR7 toward the
component and use the number buttons 0-9
to punch in the first 3-digit code for that
specific component.
If the 3-digit code number you just punched
in is the correct number, the component you
are activating will turn off.
If it did not turn
off, enter the next code number from your list
until it does turn off.
Note:
If you do not press a button within 30
seconds, the component light will turn off.
The remote will exit the set-up mode, and
you will have to start over with step three.
COMPONENT
BUTTONS
SELECT
BUTTON