Yamaha RX-V1000 Owner's Manual - Page 22

Connecting to an External Amplifier, MAIN jacks, REAR CENTER jack, CENTER jack, REAR SURROUND jacks

Get Yamaha RX-V1000 PDF manuals and user guides View all Yamaha RX-V1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

CONNECTIONS Connecting to an External Amplifier If you want to increase the power output to the speakers, or want to use another amplifier, connect an external amplifier to the PRE OUT jacks as follows. Note • When RCA pin plugs are connected to the PRE OUT jacks for output to an external amplifier, do not use the corresponding SPEAKERS terminals. 1 2 PRE OUT/MAIN IN R L MAIN IN MAIN OUT REAR SUB CENTER WOOFER 5 3 4 CENTER R REAR (SURROUND) L 1 MAIN jacks • MAIN IN jacks Line input to this unit's main channel amplifiers. • MAIN OUT jack Main channel line output jacks. Note • The signals output through these jacks are affected by the BASS, TREBLE and BASS EXTENSION settings. 2 REAR CENTER jack Rear center channel line output jack. 3 CENTER jack Center channel line output jack. 4 REAR (SURROUND) jacks Rear channel line output jacks. 5 SUBWOOFER jack When using a subwoofer with built-in amplifier, including the YAMAHA Active Servo Processing Subwoofer System, connect the input jack of the subwoofer system to this jack. Low bass signals distributed from the main, center and/or rear channels are directed to this jack. (The cut-off frequency of this jack is 90 Hz.) The LFE (low-frequency effect) signals generated when Dolby Digital or DTS is decoded are also directed if they are assigned to this jack. Notes • Adjust the volume level of the subwoofer with the control on the subwoofer. The subwoofer volume cannot be adjusted from this unit. • Depending on the settings of "1 SPEAKER SET", "10A LFE LEVEL" and "11 DTS LFE LEVEL" on the SET MENU, some signals may not be output from the SUBWOOFER jack. Connecting an External Decoder This unit is equipped with 6 additional input jacks (left and right MAIN, CENTER, left and right SURROUND and SUBWOOFER) for discrete multi-channel input from an external decoder, sound processor or pre-amplifier. Connect the output jacks on your external decoder to the 6CH INPUT jacks. Be sure to match the left and right outputs to the left and right input jacks for the main and surround channels. Notes • When you select 6CH INPUT as the input source, this unit automatically turns off the digital sound field processor, and you cannot listen to DSP programs. • When you select 6CH INPUT as the input source, changing items 1A to 1F on the SET MENU is not affected. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
18
CONNECTIONS
Connecting to an External
Amplifier
If you want to increase the power output to the speakers,
or want to use another amplifier, connect an external
amplifier to the PRE OUT jacks as follows.
Note
•
When RCA pin plugs are connected to the PRE OUT jacks for
output to an external amplifier, do not use the corresponding
SPEAKERS terminals.
1
MAIN jacks
•
MAIN IN jacks
Line input to this unit’s main channel amplifiers.
•
MAIN OUT jack
Main channel line output jacks.
Note
•
The signals output through these jacks are affected by the
BASS, TREBLE and BASS EXTENSION settings.
2
REAR CENTER jack
Rear center channel line output jack.
3
CENTER jack
Center channel line output jack.
4
REAR (SURROUND) jacks
Rear channel line output jacks.
PRE OUT/MAIN IN
MAIN
IN
MAIN
OUT
REAR
CENTER
CENTER
SUB
WOOFER
R
L
L
R
REAR
(SURROUND)
1
5
2
3
4
5
SUBWOOFER jack
When using a subwoofer with built-in amplifier,
including the YAMAHA Active Servo Processing
Subwoofer System, connect the input jack of the
subwoofer system to this jack.
Low bass signals distributed from the main, center and/or
rear channels are directed to this jack. (The cut-off
frequency of this jack is 90 Hz.) The LFE (low-frequency
effect) signals generated when Dolby Digital or DTS is
decoded are also directed if they are assigned to this jack.
Notes
•
Adjust the volume level of the subwoofer with the control on
the subwoofer. The subwoofer volume cannot be adjusted from
this unit.
•
Depending on the settings of “1 SPEAKER SET”, “10A LFE
LEVEL” and “11 DTS LFE LEVEL” on the SET MENU,
some signals may not be output from the SUBWOOFER jack.
Connecting an External Decoder
This unit is equipped with 6 additional input jacks (left
and right MAIN, CENTER, left and right SURROUND
and SUBWOOFER) for discrete multi-channel input from
an external decoder, sound processor or pre-amplifier.
Connect the output jacks on your external decoder to the
6CH INPUT jacks. Be sure to match the left and right
outputs to the left and right input jacks for the main and
surround channels.
Notes
•
When you select 6CH INPUT as the input source, this unit
automatically turns off the digital sound field processor, and
you cannot listen to DSP programs.
•
When you select 6CH INPUT as the input source, changing
items 1A to 1F on the SET MENU is not affected.