Yamaha RX-V1000 Owner's Manual - Page 60

Press and hold the button on the other, program the new function.

Get Yamaha RX-V1000 PDF manuals and user guides View all Yamaha RX-V1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

REMOTE CONTROL FEATURES 4 Press LEARN by using a ballpoint pen or similar object. "LEARN" and the selected component name appear alternately in the display window. LEARN 7 Repeat steps 5 and 6 to program additional functions. 8 Press LEARN again to exit from the learning mode. LEARN ENTER TITLE 6CH INPUT D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD CD TUNER MD/TAPE CD-R V-AUX PHONO SYSTEM POWER STANDBY MACRO OFF ON TRANSMIT RE-NAME CLEAR LEARN MACRO Note • If you do not press any button within 30 seconds during steps 5 and 6, the learning process is canceled. If this happens, start over from step 4. 5 Press the button for which you want to program the new function. "LEARN" is displayed. Notes • It is also possible to program in the control area of this unit with 10KEY/DSP set to DSP. However, if you program functions in this area, you cannot control this unit and select a DSP program. • Even if the batteries in the other remote control have enough power to transmit signals for operation, they may not have enough power to transmit signals to this remote control. • When the remote controls are either too close together or too far apart, you may not be able to program this remote control. • Direct sunlight interferes with infrared rays. • "ERROR" appears in the display window in the following circumstances: - when pressing more than one button at once; or - when MACRO ON/OFF is switched to another position. 6 Press and hold the button on the other remote control that has the function you want to program into this remote control until "OK" appears in the display window. TRANSMIT RE-NAME CLEAR LEARN MACRO SYSTEM POWER STANDBY V-AUX TUNER MD/TAPE CD-R D-TV/LD CBL/SAT VCR 1 VCR 2/DVR DVD TITLE ENTER MACRO OFF ON PHONO CD 6CH INPUT Notes • "NG" appears in the display window when programming has not been done correctly. In this case, start over from step 5. • When the memory is full, "FULL" appears in the display window, and this remote control cannot acquire any more functions. Clear unnecessary programmed functions to allow this remote control to acquire new functions. 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
56
REMOTE CONTROL FEATURES
LEARN
LEARN
TRANSMIT
RE-NAME
CLEAR
MACRO
MACRO
LEARN
OFF
ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
6CH INPUT
TITLE
ENTER
TRANSMIT
RE-NAME
CLEAR
MACRO
MACRO
LEARN
OFF
ON
SYSTEM
POWER
STANDBY
PHONO
V-AUX
TUNER
MD/TAPE
CD-R
CD
D-TV/LD
CBL/SAT
VCR 1
VCR 2/DVR
DVD
6CH INPUT
TITLE
ENTER
4
Press LEARN by using a ballpoint pen or
similar object.
“LEARN” and the selected component name appear
alternately in the display window.
Note
•
If you do not press any button within 30 seconds during steps 5
and 6, the learning process is canceled. If this happens, start
over from step 4.
5
Press the button for which you want to
program the new function.
“LEARN” is displayed.
6
Press and hold the button on the other
remote control that has the function you
want to program into this remote control
until “OK” appears in the display window.
Notes
•
“NG” appears in the display window when programming has
not been done correctly. In this case, start over from step 5.
•
When the memory is full, “FULL” appears in the display
window, and this remote control cannot acquire any more
functions. Clear unnecessary programmed functions to allow
this remote control to acquire new functions.
7
Repeat steps 5 and 6 to program additional
functions.
8
Press LEARN again to exit from the learning
mode.
Notes
•
It is also possible to program in the control area of this unit
with 10KEY/DSP set to DSP. However, if you program
functions in this area, you cannot control this unit and select a
DSP program.
•
Even if the batteries in the other remote control have enough
power to transmit signals for operation, they may not have
enough power to transmit signals to this remote control.
•
When the remote controls are either too close together or too
far apart, you may not be able to program this remote control.
•
Direct sunlight interferes with infrared rays.
•
“ERROR” appears in the display window in the following
circumstances:
– when pressing more than one button at once; or
– when MACRO ON/OFF is switched to another position.