Yamaha RX V2700 MCXSP10 Manual - Page 152

During Auto Setup, After Auto Setup, Error message, Cause, Remedy, Warning message - service manual

Get Yamaha RX V2700 - AV Network Receiver PDF manuals and user guides
UPC - 027108927077
View all Yamaha RX V2700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 152 highlights

TROUBLESHOOTING During Auto Setup Error message E01:No Front SP E02:No Sur. SP E03:No PRNS SP E04:SBR->SBL E05:Noisy E06:Check Sur. E07:No MIC E08:No Signal E09:User Cancel E10:Internal Err. After Auto Setup Cause Remedy Front L/R channel signals are not detected. Check the front L/R speaker connections. A surround channel signal is not detected. Check the surround speaker connections. A presence channel signal is not detected. Check the presence speaker connections. Only right surround back channel signal is detected. Connect the surround back speaker to the LEFT SURROUND BACK SPEAKERS terminal if you only have one surround back speaker. Background noise is too loud. Try running "Auto Setup" in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. Surround back speakers are connected, though surround L/R speakers are not. Connect surround speakers when you use surround back speakers. The optimizer microphone was unplugged during the "Auto Setup" procedure. Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. The optimizer microphone does not detect test tones. Check the microphone setting. Check the speaker connections and placement. The "Auto Setup" procedure was cancelled Run "Auto Setup" again. due to user activity. An internal error occurred. Run "Auto Setup" again. See page 16 16 16 16 - - 16 35 35 16 35 35 Warning message Cause Remedy W1:Out of Phase W2:Over Distance W3:Level Error W4:SP Mismatch Speaker polarity is not correct. This message may appear depending on the speakers even when the speakers are connected correctly. The distance between the speaker and the listening position is over 24 m (80 ft). The difference of volume level among speakers is excessive. The result of the wiring check of "Auto Setup" is different from "Speaker Set" in "Manual Setup". Check the speaker connections for proper polarity (+ or -). Bring the speaker closer to the listening position. Readjust the speaker installation so that all speakers are set in locations with similar conditions. Check the speaker connections. Use speakers of similar quality. Adjust the output volume of the subwoofer. Use "Speaker Set" in "Manual Setup" to adjust the speaker settings manually. Notes • If the "ERROR" or "WARNING" screens appears, check the cause of the problem, then run "Auto Setup" again. • If warning "W1" appears, corrections are made, but they may not be optimal. • If warning "W2" or "W3" appears, no corrections are made. • If error "E10" occurs repeatedly, please contact a qualified YAMAHA service center. See page 16 - - 16 - 35 105 148 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
148
En
TROUBLESHOOTING
During Auto Setup
After Auto Setup
•
If the “ERROR” or “WARNING” screens appears, check the cause of the problem, then run “Auto Setup” again.
•
If warning “W1” appears, corrections are made, but they may not be optimal.
•
If warning “W2” or “W3” appears, no corrections are made.
•
If error “E10” occurs repeatedly, please contact a qualified YAMAHA service center.
Error message
Cause
Remedy
See
page
E01:No Front SP
Front L/R channel signals are not detected.
Check the front L/R speaker connections.
16
E02:No Sur. SP
A surround channel signal is not detected.
Check the surround speaker connections.
16
E03:No PRNS SP
A presence channel signal is not detected.
Check the presence speaker connections.
16
E04:SBR->SBL
Only right surround back channel signal is
detected.
Connect the surround back speaker to the
LEFT SURROUND BACK SPEAKERS
terminal if you only have one surround
back speaker.
16
E05:Noisy
Background noise is too loud.
Try running “Auto Setup” in a quiet
environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the
optimizer microphone.
—
E06:Check Sur.
Surround back speakers are connected,
though surround L/R speakers are not.
Connect surround speakers when you use
surround back speakers.
16
E07:No MIC
The optimizer microphone was unplugged
during the “Auto Setup” procedure.
Connect the supplied optimizer microphone
to the OPTIMIZER MIC jack on the front
panel.
35
E08:No Signal
The optimizer microphone does not detect
test tones.
Check the microphone setting.
35
Check the speaker connections and
placement.
16
E09:User Cancel
The “Auto Setup” procedure was cancelled
due to user activity.
Run “Auto Setup” again.
35
E10:Internal Err.
An internal error occurred.
Run “Auto Setup” again.
35
Warning message
Cause
Remedy
See
page
W1:Out of Phase
Speaker polarity is not correct. This
message may appear depending on the
speakers even when the speakers are
connected correctly.
Check the speaker connections for proper
polarity (+ or –).
16
W2:Over Distance
The distance between the speaker and the
listening position is over 24 m (80 ft).
Bring the speaker closer to the listening
position.
—
W3:Level Error
The difference of volume level among
speakers is excessive.
Readjust the speaker installation so that all
speakers are set in locations with similar
conditions.
—
Check the speaker connections.
16
Use speakers of similar quality.
—
Adjust the output volume of the subwoofer.
35
W4:SP Mismatch
The result of the wiring check of “Auto
Setup” is different from “Speaker Set” in
“Manual Setup”.
Use “Speaker Set” in “Manual Setup” to
adjust the speaker settings manually.
105
Notes