Yamaha RX-V683 RX-V683 Owner s Manual - Page 44

Error messages, E-3: No F.PRNS SP

Get Yamaha RX-V683 PDF manuals and user guides View all Yamaha RX-V683 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Error messages If any error message is displayed during the measurement, resolve the problem and perform YPAO again. Error message E-1: No Front SP E-2: No Sur. SP E-3: No F.PRNS SP E-4: SBR ➞ SBL E-5: Noisy E-6: Check Sur. E-7: No MIC E-8: No Signal E-9: User Cancel E-10: Internal Error Cause Remedy Front speakers are not detected. One of the surround speakers cannot be detected. Follow the on-screen instructions to exit YPAO, turn off the unit, and then check the speaker connections. One of the presence speakers cannot be detected. A surround back speaker is connected to the R side only. When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow the on-screen instructions to exit YPAO, turn off the unit, and then reconnect the speaker. The noise is too loud. Keep the room quiet and follow the on-screen instructions to start the measurement again. If you select "PROCEED", YPAO takes the measurement again and ignores any noise detected. Surround back speakers are connected, but no surround speakers Surround speakers need to be connected in order to use surround back speakers. Follow the on-screen instructions are connected. to exit YPAO, turn off the unit, and then reconnect the speakers. The YPAO microphone has been removed. Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the measurement again. The YPAO microphone cannot detect test tones. Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the measurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. The measurement has been canceled. Follow the on-screen instructions to start the measurement again. To cancel the measurement, select "EXIT". An internal error has occurred. Follow the on-screen instructions to exit YPAO, turn off and on the unit. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center. En 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
En
44
Error messages
If any error message is displayed during the measurement, resolve the problem and perform YPAO again.
Error message
Cause
Remedy
E-1: No Front SP
Front speakers are not detected.
Follow the on-screen instructions to exit YPAO, turn off the unit, and then check the speaker connections.
E-2: No Sur. SP
One of the surround speakers cannot be detected.
E-3: No F.PRNS SP
One of the presence speakers cannot be detected.
E-4: SBR
➞
SBL
A surround back speaker is connected to the R side only.
When using only one surround back speaker, you need to connect it to the SINGLE jack (L side). Follow the on-screen
instructions to exit YPAO, turn off the unit, and then reconnect the speaker.
E-5: Noisy
The noise is too loud.
Keep the room quiet and follow the on-screen instructions to start the measurement again. If you select “PROCEED”,
YPAO takes the measurement again and ignores any noise detected.
E-6: Check Sur.
Surround back speakers are connected, but no surround speakers
are connected.
Surround speakers need to be connected in order to use surround back speakers. Follow the on-screen instructions
to exit YPAO, turn off the unit, and then reconnect the speakers.
E-7: No MIC
The YPAO microphone has been removed.
Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the
measurement again.
E-8: No Signal
The YPAO microphone cannot detect test tones.
Connect the YPAO microphone to the YPAO MIC jack firmly and follow the on-screen instructions to start the
measurement again. If this error occurs repeatedly, contact the nearest authorized Yamaha dealer or service center.
E-9: User Cancel
The measurement has been canceled.
Follow the on-screen instructions to start the measurement again. To cancel the measurement, select “EXIT”.
E-10: Internal Error
An internal error has occurred.
Follow the on-screen instructions to exit YPAO, turn off and on the unit. If this error occurs repeatedly, contact the
nearest authorized Yamaha dealer or service center.