Yamaha V665 Owners Manual - Page 22

Connecting the FM and AM antennas, Connecting the power cable, Turning this unit on and off - zone 2

Get Yamaha V665 - RX AV Receiver PDF manuals and user guides
UPC - 027108933061
View all Yamaha V665 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Connections Connecting the FM and AM antennas An indoor FM antenna and an AM loop antenna are supplied with this unit. Connect these antennas properly to the respective jacks. Connecting the power cable After all connections are complete, plug the AC power cable of this unit into an AC wall outlet. Indoor FM antenna Outdoor AM antenna Connect a 5 to 10 m (16 to 33 ft) vinyl-covered wire, and extend it outdoors (use the AM loop antenna together with this antenna). AM loop antenna US DOCK COMPONENT VIDEO PR PB Y (BD/DVD) XM HDMI OUT HDMI 1 HDMI 2 HDMI 3 H ANTENNA UNBAL. COMPONENT VIDEO REMOTE PR IN OUT FM GND AM PB VIDEO VIDEO Y MONITOR OUT 12V 0.1A MAX. TRIGGER OUT FRO CENTER Ground (GND terminal) The GND terminal is not for earth grounding. To reduce noises, connect a ground bar or a vinyl-covered wire with a copper plate at its tip, and place it in the moist ground. y • The supplied antennas are normally sensitive enough to obtain good reception. • Position the AM loop antenna away from this unit. • If you cannot get good reception, we recommend that you use an outdoor antenna. For more details, consult the nearest authorized Yamaha dealer or service center. • Always use the AM loop antenna even when the outdoor antenna is connected. Assembling the AM loop antenna Connecting the AM loop antenna The wires of the AM loop antenna have no polarity. You can connect either wire to the AM terminal and the other to the GND terminal. To the AC wall outlet Power cable Turning this unit on and off 1 Press AMAIN ZONE ON/OFF on the front panel (or gPOWER on the remote control) to turn on this unit. 2 Press AMAIN ZONE ON/OFF (or gPOWER) again to turn off this unit (standby mode). y • The unit needs a few seconds until ready to play back. • You can also turn on this unit by pressing JSCENE (or lSCENE). • This unit consumes a small amount of electricity even in the standby mode. We recommend disconnecting the power cable from the AC wall outlet. Caution Do not unplug this unit while it is turned on. Doing so may damage this unit or cause the settings of this unit to be saved incorrectly. Press and hold Insert Release 18 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
18
En
Connections
An indoor FM antenna and an AM loop antenna are
supplied with this unit. Connect these antennas properly to
the respective jacks.
y
•
The supplied antennas are normally sensitive enough to obtain good
reception.
•
Position the AM loop antenna away from this unit.
•
If you cannot get good reception, we recommend that you use an outdoor
antenna. For more details, consult the nearest authorized Yamaha dealer
or service center.
•
Always use the AM loop antenna even when the outdoor antenna is
connected.
Assembling the AM loop antenna
Connecting the AM loop antenna
The wires of the AM loop antenna have no polarity. You
can connect either wire to the AM terminal and the other
to the GND terminal.
After all connections are complete, plug the AC power
cable of this unit into an AC wall outlet.
1
Press
A
MAIN ZONE ON/OFF
on the front
panel (or
g
POWER
on the remote control)
to turn on this unit.
2
Press
A
MAIN ZONE ON/OFF
(or
g
POWER
) again to turn off this unit
(standby mode).
y
•
The unit needs a few seconds until ready to play back.
•
You can also turn on this unit by pressing
J
SCENE
(or
l
SCENE
).
•
This unit consumes a small amount of electricity even in the standby
mode. We recommend disconnecting the power cable from the AC wall
outlet.
Connecting the FM and AM antennas
ANTENNA
UNBAL.
FM
GND
AM
US
XM
DOCK
COMPONENT
VIDEO
P
R
P
B
Y
VIDEO
HDMI
HDMI 1
(
BD/DVD
)
HDMI 2
HDMI 3
H
VIDEO
IN
OUT
MONITOR OUT
TRIGGER OUT
12V
0.1A MAX.
FRO
CENTER
P
R
P
B
Y
REMOTE
COMPONENT
VIDEO
OUT
Outdoor AM antenna
Connect a 5 to 10 m (16 to
33 ft) vinyl-covered wire,
and extend it outdoors
(use the AM loop antenna
together with this
antenna).
Ground (GND terminal)
The GND terminal is not for earth grounding.
To reduce noises, connect a ground bar or a
vinyl-covered wire with a copper plate at its tip,
and place it in the moist ground.
Indoor FM antenna
AM loop
antenna
Press and hold
Release
Insert
Connecting the power cable
Turning this unit on and off
Caution
Do not unplug this unit while it is turned on. Doing so
may damage this unit or cause the settings of this unit
to be saved incorrectly.
To the AC wall outlet
Power cable