Yamaha V665 Owners Manual - Page 73

Auto Setup YPAO

Get Yamaha V665 - RX AV Receiver PDF manuals and user guides
UPC - 027108933061
View all Yamaha V665 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

INTRODUCTION PREPARATION BASIC OPERATION Troubleshooting Auto Setup (YPAO) Notes • If the "ERROR" or "WARNING" screen appears, resolve the problem and then run "Auto Setup" again. • Warning message "W-2" or "W-3" indicates that the adjusted settings may not be optimal. • Depending on the speakers, warning message "W-1" may appears even if the speaker connections are correct. • If error message "E-10" occurs repeatedly, contact a qualified Yamaha service center. Before Auto Setup Error message Connect MIC! Unplug HP! Memory Guard! Cause Remedy Optimizer microphone is not connected. Headphones are connected. The parameters of this unit are protected. Connect the supplied optimizer microphone to the OPTIMIZER MIC jack on the front panel. Unplug the headphones. Set "Memory Guard" to "Off." During Auto Setup See page 19 - 56 Error message Cause Remedy E-1:NO FRONT SP Front L/R channel signals are not detected. Check the front L/R speaker connections. E-2:NO SUR. SP Only a signal from one of the surround channels are detected. Check the surround L/R speaker connections. E-3:NO PRNS SP Only signals from one of the presence L/ Check the presence L/R speaker connections. R channels are detected. E-4:SBR->SBL Only right surround back channel signal If you connect only one surround back speaker, is detected. connect it to the L-side (SINGLE) terminal. E-5:NOISY Measurement cannot be performed accurately due to loud ambient noise. Try running "Auto Setup" in a quiet environment. Turn off noisy electric equipment like air conditioners or move them away from the optimizer microphone. E-6:CHECK SUR. Surround back speakers are connected, though surround L/R speakers are not. When using surround back speakers, you need to connect surround L/R speakers. E-7:NO MIC The optimizer microphone was unplugged during the "Auto Setup" procedure. Do not touch the optimizer microphone during "Auto Setup." E-8:NO SIGNAL The optimizer microphone does not detect test tones. Check whether the microphone is properly placed. Check whether the speakers are properly placed and connected. The optimizer microphone or OPTIMIZER MIC jack may be defective. Contact the nearest Yamaha dealer or service center. E-9:USER CANCEL "Auto Setup" was cancelled due to an inappropriate user operation. Run "Auto Setup" again. E-10:INTERNAL ERROR An internal error occurred. Run "Auto Setup" again. See page 11 11 11 11 - - 11 19 19 11 19 19 19 ADVANCED OPERATION APPENDIX English 69 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
69
En
Troubleshooting
English
INTRODUCTION
APPENDIX
PREPARATION
BASIC
OPERATION
ADVANCED
OPERATION
Notes
•
If the “ERROR” or “WARNING” screen appears, resolve the problem and then run “Auto Setup” again.
•
Warning message “W-2” or “W-3” indicates that the adjusted settings may not be optimal.
•
Depending on the speakers, warning message “W-1” may appears even if the speaker connections are correct.
•
If error message “E-10” occurs repeatedly, contact a qualified Yamaha service center.
Auto Setup (YPAO)
Before Auto Setup
Error message
Cause
Remedy
See
page
Connect MIC!
Optimizer microphone is not connected.
Connect the supplied optimizer microphone to the
OPTIMIZER MIC jack on the front panel.
19
Unplug HP!
Headphones are connected.
Unplug the headphones.
—
Memory Guard!
The parameters of this unit are protected.
Set “Memory Guard” to “Off.”
56
During Auto Setup
Error message
Cause
Remedy
See
page
E-1:NO FRONT SP
Front L/R channel signals are not
detected.
Check the front L/R speaker connections.
11
E-2:NO SUR. SP
Only a signal from one of the surround
channels are detected.
Check the surround L/R speaker connections.
11
E-3:NO PRNS SP
Only signals from one of the presence L/
R channels are detected.
Check the presence L/R speaker connections.
11
E-4:SBR->SBL
Only right surround back channel signal
is detected.
If you connect only one surround back speaker,
connect it to the L-side (SINGLE) terminal.
11
E-5:NOISY
Measurement cannot be performed
accurately due to loud ambient noise.
Try running “Auto Setup” in a quiet environment.
—
Turn off noisy electric equipment like air
conditioners or move them away from the optimizer
microphone.
—
E-6:CHECK SUR.
Surround back speakers are connected,
though surround L/R speakers are not.
When using surround back speakers, you need to
connect surround L/R speakers.
11
E-7:NO MIC
The optimizer microphone was
unplugged during the “Auto Setup”
procedure.
Do not touch the optimizer microphone during “Auto
Setup.”
19
E-8:NO SIGNAL
The optimizer microphone does not
detect test tones.
Check whether the microphone is properly placed.
19
Check whether the speakers are properly placed and
connected.
11
The optimizer microphone or OPTIMIZER MIC
jack may be defective. Contact the nearest Yamaha
dealer or service center.
19
E-9:USER CANCEL
“Auto Setup” was cancelled due to an
inappropriate user operation.
Run “Auto Setup” again.
19
E-10:INTERNAL ERROR
An internal error occurred.
Run “Auto Setup” again.
19