ASRock X79 Extreme11 LSI SAS2 Integrated RAID Solution User Guide - Page 37

Out of Sync OSY

Get ASRock X79 Extreme11 PDF manuals and user guides View all ASRock X79 Extreme11 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

SAS2 Integrated RAID Solution User Guide A.3.5 HOTSPARE Command Appendix A: | Commands Logical drive status values are as follows:  Okay (OKY) - The volume is active and drives are functioning properly. User data is protected if the current RAID level provides data protection.  Degraded (DGD) - The volume is active. User data is not fully protected because the configuration has changed or a drive has failed.  Failed (FLD) - The volume has failed.  Missing (MIS) - The volume is missing.  Initializing (INIT) - The volume is initializing.  Online (ONL) - The volume is online. Physical device status values are as follows:  Online (ONL) - The drive is operational and is part of a logical drive.  Hot Spare (HSP) - The drive is a hot spare that is available to replace a failed drive in an array.  Ready (RDY) - The drive is ready for use as a normal disk drive, or it is ready to be assigned to a disk array or a hot spare pool.  Available (AVL) - The drive may or may not be ready, and it is not suitable for use in an array or a hot spare pool.  Failed (FLD) - The drive failed and is now offline.  Missing (MIS) - The drive has been removed or is not responding.  Standby (SBY) - The device is not a hard-disk device.  Out of Sync (OSY) - The drive, which is part of a logical drive, is not in sync with other drives that are part of the logical drive.  Degraded (DGD) - The drive is part of a logical drive and is in degraded state.  Rebuilding (RBLD) - The drive is part of a logical drive and is currently rebuilding.  Optimal (OPT) - The drive is optimal and is part of a logical drive. Physical device Drive Type values are as follows:  SAS_HDD - The drive is a SAS HDD.  SATA_HDD - The drive is a SATA HDD.  SAS_SSD - The drive is a SAS SSD.  SATA_SSD - The drive is a SATA SSD. Physical device Protocol values are as follows:  SAS - The drive supports SAS protocol.  SATA - The drive supports SATA protocol. The HOTSPARE command adds a hot spare drive to spare pool 0 or deletes a hot spare drive. The capacity of the hot spare drive must be greater than or equal to the capacity of the smallest drive in the RAID volume. You can verify this by using the DISPLAY command on the drive. LSI Corporation Confidential | August 2010 Page 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
SAS2 Integrated RAID Solution User Guide
Appendix A:
|
Commands
LSI Corporation Confidential
|
August 2010
Page 37
Logical drive status values are as follows:
Okay (OKY)
–
The volume is active and drives are functioning properly. User data
is protected if the current RAID level provides data protection.
Degraded
(DGD)
– The volume is active. User data is not fully protected because
the configuration has changed or a drive has failed.
Failed (FLD)
– The volume has failed.
Missing (MIS)
– The volume is missing.
Initializing (INIT)
– The volume is initializing.
Online (ONL)
– The volume is online.
Physical device status values are as follows:
Online (ONL)
–
The drive is operational and is part of a logical drive.
Hot Spare (HSP)
–
The drive is a hot spare that is available to replace a failed
drive in an array.
Ready (RDY)
–
The drive is ready for use as a normal disk drive, or it is ready to be
assigned to a disk array or a hot spare pool.
Available (AVL)
–
The drive may or may not be ready, and it is not suitable for
use in an array or a hot spare pool.
Failed (FLD)
– The drive failed and is now offline.
Missing (MIS)
– The drive has been removed or is not responding.
Standby (SBY)
–
The device is not a hard-disk device.
Out of Sync (OSY)
– The drive, which is part of a logical drive, is not in sync
with other drives that are part of the logical drive.
Degraded (DGD)
– The drive is part of a logical drive and is in degraded state.
Rebuilding (RBLD)
– The drive is part of a logical drive and is
currently rebuilding.
Optimal (OPT)
– The drive is optimal and is part of a logical drive.
Physical device Drive Type values are as follows:
SAS_HDD
–
The drive is a SAS HDD.
SATA_HDD
– The drive is a SATA HDD.
SAS_SSD
– The drive is a SAS SSD.
SATA_SSD
– The drive is a SATA SSD.
Physical device Protocol values are as follows:
SAS
– The drive supports SAS protocol.
SATA
– The drive supports SATA protocol.
A.3.5
HOTSPARE Command
The HOTSPARE command adds a hot spare drive to spare pool 0 or deletes a hot spare
drive. The capacity of the hot spare drive must be greater than or equal to the capacity
of the smallest drive in the RAID volume. You can verify this by using the DISPLAY
command on the drive.