Brother International CS-8072 Users Manual - English - Page 42

When Sewing Straight Stitches only, Upper thread

Get Brother International CS-8072 PDF manuals and user guides View all Brother International CS-8072 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

CONTENTS BEFORE USE SEWING UTILITY STITCHES 7. Make a cut of about 20 mm (3/4'') in the fabric. 1 20 mm (3/4'') 1 2 A 13 5 6 B 5 6 1 8. Place the fabric on foot as shown in figure B. - Right side of cut: on top of the guide plate - Left side of cut: underneath the presser foot 1 Guide plate (lower knife) 2 Presser foot 9. Thread the needle, then pull out a long section of the upper thread, pass it below the presser foot and pull it out in the fabric feed direction (see figure B). 2 Presser foot 3 Upper thread CAUTION If the width has been adjusted, turn the balance wheel by hand and check that the needle does not touch the side cutter. If the needle hits the side cutter, the needle may break and cause injury. When Sewing Straight Stitches only The seam margin should be about 5 mm (3/16''). 1 Seam margin * Make sure you select a pattern for the side cutter. * Clean the side cutter after use, to avoid having dust and scraps of thread build up on it. * Add a small amount of oil as required to the cutting edge of the cutter. Note - The fabric will not be cut if the whole fabric is simply spread out underneath the presser foot guide plate. Set the fabric as explained in step 8, and then start sewing. - Check that the needle is raised when the presser foot lever is raised. - One layer of 13 oz. denim can be cut. MAINTENANCE SEWING CHART PATTERNS (PROGRAMMED IN MACHINE) 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
39
CONTENTS
BEFORE USE
SEWING
UTILITY STITCHES
MAINTENANCE
SEWING CHART
PATTERNS
(PROGRAMMED IN
MACHINE)
1
5
6
1
3
2
A
B
5
6
7.
Make a cut of about 20 mm (3/4'') in the fabric.
1
20 mm (3/4'')
1
8.
Place the fabric on foot as shown in figure B.
-
Right side of cut: on top of the guide plate
-
Left side of cut: underneath the presser foot
1
Guide plate (lower knife)
2
Presser foot
9.
Thread the needle, then pull out a long section
of the upper thread, pass it below the presser
foot and pull it out in the fabric feed direction
(see figure B).
2
Presser foot
3
Upper thread
CAUTION
If the width has been adjusted, turn the
balance wheel by hand and check that
the needle does not touch the side
cutter. If the needle hits the side cutter,
the needle may break and cause injury.
When Sewing Straight Stitches only
The seam margin should be about 5 mm (3/16'').
1
Seam margin
*
Make sure you select a pattern for the side cut-
ter.
*
Clean the side cutter after use, to avoid having
dust and scraps of thread build up on it.
*
Add a small amount of oil as required to the
cutting edge of the cutter.
Note
–
The fabric will not be cut if the whole fabric is
simply spread out underneath the presser foot
guide plate. Set the fabric as explained in step
8, and then start sewing.
–
Check that the needle is raised when the presser
foot lever is raised.
–
One layer of 13 oz. denim can be cut.