Brother International IntelliFax-2600 Service Manual - Page 141

Refer to V, PC BUSY OR FAIL

Get Brother International IntelliFax-2600 PDF manuals and user guides View all Brother International IntelliFax-2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 141 highlights

Messages on the LCD DOCUMENT JAM Probable Cause Document loading error (1) The document rear sensor detects no leading edge of a document within 10 seconds from the start of document loading operation. (The document rear sensor stays OFF even after the document has been fed when the document front sensor was ON.) (2) The loaded document is too short. (Since the document is shorter than the distance between the document front and rear sensors, the document front sensor is turned OFF before the document rear sensor is turned ON.) CLEAN UP SCANNER In the scanning compensation data list printed by the maintenance-mode function code 05, less than fifty percent of the white level data is faulty. (This message may appear only in the maintenance mode.) SCANNER ERROR In the scanning compensation data list printed by the maintenance-mode function code 05, fifty percent or more of the white level data is faulty. (This message may appear only in the maintenance mode.) TONER LOW The toner sensor has detected that there is not enough toner. TONER EMPTY The toner sensor has detected that there is no toner. If this message appears, recording is no longer possible. SET CARTRIDGE The toner sensor has detected that no toner cartridge is loaded. COOLING DOWN PLEASE WAIT (Appear alternately.) MACHINE ERROR XX CHANGE DRUM SOON PC BUSY OR FAIL The toner thermister has detected that the toner temperature exceeded the specified level. If the temperature exceeds the preset level, recording is no longer possible. "XX" indicates an error code. Refer to [ 2 ] on pages VI-4 and VI-5. The service life of the drum unit will expire soon. This message appears for one minute. (You can turn this message indication on or off by the maintenance-mode function code 10, WSW31, selector 8. Refer to Chapter V, Section 3.5.) After connected with the host computer, the equipment has received no response from the computer. (A communications error has occurred.) VI - 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
VI
- 2
Messages on the LCD
Probable Cause
DOCUMENT JAM
±
Document loading error
(1)
The document rear sensor detects no leading edge of a
document within 10 seconds from the start of document
loading operation.
(The document rear sensor stays OFF even after the
document has been fed when the document front sensor
was ON.)
(2)
The loaded document is too short.
(Since the document is shorter than the distance between
the document front and rear sensors, the document front
sensor is turned OFF before the document rear sensor is
turned ON.)
CLEAN UP SCANNER
In the scanning compensation data list printed by the mainte-
nance-mode function code 05, less than fifty percent of the white
level data is faulty.
(This message may appear only in the maintenance mode.)
SCANNER ERROR
In the scanning compensation data list printed by the
maintenance-mode function code 05, fifty percent or more of the
white level data is faulty.
(This message may appear only in the maintenance mode.)
TONER LOW
The toner sensor has detected that there is not enough toner.
TONER EMPTY
The toner sensor has detected that there is no toner.
If this
message appears, recording is no longer possible.
SET CARTRIDGE
The toner sensor has detected that no toner cartridge is loaded.
COOLING DOWN
PLEASE WAIT
(Appear alternately.)
The toner thermister has detected that the toner temperature
exceeded the specified level.
If the temperature exceeds the
preset level, recording is no longer possible.
MACHINE ERROR XX
"XX" indicates an error code.
Refer to [ 2 ] on pages VI-4 and
VI-5.
CHANGE DRUM SOON
The service life of the drum unit will expire soon.
This message
appears for one minute.
(You can turn this message indication on or off by the
maintenance-mode function code 10, WSW31, selector 8.
Refer to Chapter V, Section 3.5.)
PC BUSY OR FAIL
After connected with the host computer, the equipment has
received no response from the computer.
(A communications
error has occurred.)