Brother International IntelliFax-2600 Service Manual - Page 41

Panel Rear Cover and Control Panel

Get Brother International IntelliFax-2600 PDF manuals and user guides View all Brother International IntelliFax-2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

1.5 Panel Rear Cover and Control Panel (1) Place the control panel ASSY upside down. If you do not need to remove the ADF parts, anti-static brush, shield film, document pressure bar, or document rear sensor actuator, skip to step (6). (2) To remove the ADF parts (spring plates, separation rubber and anti-vibration rubber), remove the screw. (3) To replace the anti-static brush and shield film, remove them. NOTE: Once removed, the anti-static brush and shield film will become unusable and new parts will have to be put back in. (4) To remove the document pressure bar, pull either of supports "a" provided on the panel rear cover outwards and then lift the pressure bar up and towards the rear to release the three tabs from the cutouts provided in the panel rear cover. The spring also comes off. (5) To remove the document rear sensor actuator, pull either of supports "b" on the panel rear cover outwards. IV - 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
IV
- 9
1.5
Panel Rear Cover and Control Panel
(1)
Place the control panel ASSY upside down.
If you do not need to remove the ADF parts, anti-static brush, shield film, document pressure
bar, or document rear sensor actuator, skip to step (6).
(2)
To remove the ADF parts (spring plates, separation rubber and anti-vibration rubber), remove
the screw.
(3)
To replace the anti-static brush and shield film, remove them.
NOTE:
Once removed, the anti-static brush and shield film will become unusable and new
parts will have to be put back in.
(4)
To remove the document pressure bar, pull either of supports "a" provided on the panel rear
cover outwards and then lift the pressure bar up and towards the rear to release the three tabs
from the cutouts provided in the panel rear cover.
The spring also comes off.
(5)
To remove the document rear sensor actuator, pull either of supports "b" on the panel rear
cover outwards.