Brother International SB3150 Operation Manual - Page 53

Stitch Setting Chart Stitch Setting Chart STARTING TO SEW Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. This table applies to several models (Model 3, 2 and 1). Refer to the Quick Reference Guide for the model of your machine. *1 Patterns printed on the numeric keys on the machine can be selected directly. For details, refer to "Preset utility stitches" on page B-51. *2 For free motion quilting, use free motion open toe quilting foot "O" (sold separately with some models). *3 When (Automatic reverse/reinforcement key) is activated, the stitch will begin with reinforcement stitch. If (Reinforcement priority) on the settings screen is also set to "ON", the machine will sew reinforcement stitches at the end of stitching and then stop. B Note • The walking foot can only be used with straight or zigzag stitch patterns. Do not sew reverse stitches with the walking foot. Stitch width Stitch length [mm (inch)] [mm (inch)] Model 3, 2 Model 1 Stitch Stitch name Presser foot Applications Stitch number Straight stitch 01*1 01*1 (Left) General sewing, gather, J*2 pintuck, etc. Straight stitch 02*1 02*1 (Left) General sewing, gather, J*2 pintuck, etc. Straight stitch 03*1 03*1 (Middle) General sewing, gather, J*2 pintuck, etc. Straight stitch 04*1 04*1 (Middle) General sewing, gather, J*2 pintuck, etc. Triple stretch 05*1 05*1 stitch Stem stitch 06*1 06*1 General sewing for J*2 reinforcement and decorative topstitching Reinforced stitching, sewing J*2 and decorative applications Decorative stitch Decorative stitching, top 07 - N*2 stitching Basting stitch Basting 08 07 J*2 Zigzag stitch 09*1 08*1 Zigzag stitch 10*1 09*1 Zigzag stitch 11 10 (Right) For overcasting, mending. J*2 For overcasting, mending. J*2 Start from right needle J*2 position, zigzag sews to left. Auto. Manual Auto. Manual Twin needle 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) OK ( J ) 1.0 (1/16) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) OK ( J ) Model 3, 2: 0.0 (0) 0.0 - 7.0 (0 - 1/4) 20 (3/4) 5 - 30 (3/16 - 1-3/16) Model 1: NO - 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.0 - 5.0 (0 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.0 - 5.0 (0 - 3/16) OK ( J ) 3.5 (1/8) 2.5 - 5.0 (3/32 - 3/16) 1.4 (1/16) 0.3 - 5.0 (1/64 - 3/16) OK ( J ) Reverse button Reverse Reverse*3 Reverse Reverse*3 Reinforce- ment Reinforce- ment Reinforce- ment Reinforcement Reverse Reverse*3 Reverse*3 Basic operations B-45