Brother International Simplicity SB530T Users Manual - English and Spanish - Page 25

Drawing up the lower, thread

Get Brother International Simplicity SB530T PDF manuals and user guides View all Brother International Simplicity SB530T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Pull the loop of the thread passed through h the eye of the needle toward the rear of Pass the end of the thread through the j presser foot, and then pull out about 5 cm the machine. (2 inches) of thread toward the rear of the machine. 1 1 1 Loop of thread CAUTION ● Be careful not to pull on the thread with force or it may bend the needle. ● If the thread does not pass through the eye of the needle, start from step c again. 1 1 5 cm (2 inches) Note ● If you incorrectly feed the thread you may cause sewing problems. Note ● Needle threader cannot be used when using the twin needle. In this case, thread the needle as described below. Raise the presser foot lever. i Drawing up the lower thread You can begin sewing immediately without drawing up the bobbin thread. When sewing gathers or darts, you can draw up the lower thread by hand so that some thread will be left over. Before you draw up the lower thread, put the bobbin back in. Raise the presser foot lever. 1 Remove the bobbin cover, and then 2 reinstall the bobbin. Pass the thread along the slit in the 3 direction of the arrow, and leave it there without cutting it. • The bobbin cover should still be removed. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
24
————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————————
1
h
Pull the loop of the thread passed through
the eye of the needle toward the rear of
the machine.
1
Loop of thread
CAUTION
Note
●
Needle threader cannot be used when using
the twin needle. In this case, thread the
needle as described below.
i
Raise the presser foot lever.
j
Pass the end of the thread through the
presser foot, and then pull out about 5 cm
(2 inches) of thread toward the rear of the
machine.
1
5 cm (2 inches)
Note
●
If you incorrectly feed the thread you may
cause sewing problems.
Drawing up the lower
thread
You can begin sewing immediately without drawing up
the bobbin thread.
When sewing gathers or darts, you can draw up the
lower thread by hand so that some thread will be left
over. Before you draw up the lower thread, put the
bobbin back in.
1
Raise the presser foot lever.
2
Remove the bobbin cover, and then
reinstall the bobbin.
3
Pass the thread along the slit in the
direction of the arrow, and leave it there
without cutting it.
•
The bobbin cover should still be removed.
●
Be careful not to pull on the thread with
force or it may bend the needle.
●
If the thread does not pass through the
eye of the needle, start from step
c
again.
1
1