Home » Cisco Manuals » Wireless » Cisco AIR-AP1242AG-A-K9 » Manual Viewer

Cisco AIR-AP1242AG-A-K9 Hardware Installation Guide - Page 117

Extensible Authentication Protocol. An optional IEEE 802.1x security feature - australia

UPC - 882658021961

View all Cisco AIR-AP1242AG-A-K9 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Glossary DHCP dipole domain name DNS DSSS Dynamic host configuration protocol. A protocol available with many operating systems that automatically issues IP addresses within a specified range to devices on the network. The device retains the assigned address for a specific administrator-defined period. A type of low-gain (2.2-dBi) antenna consisting of two (often internal) elements. The text name that refers to a grouping of networks or network resources based on organization-type or geography; for example: name.com-commercial; name.edu-educational; name.gov-government; ISPname.net-network provider (such as an ISP); name.ar-Argentina; name.au-Australia; and so on. Domain Name System server. A server that translates text names into IP addresses. The server maintains a database of host alphanumeric names and their corresponding IP addresses. Direct sequence spread spectrum. A type of spread spectrum radio transmission that spreads its signal continuously over a wide frequency band. E EAP Ethernet Extensible Authentication Protocol. An optional IEEE 802.1x security feature ideal for organizations with a large user base and access to an EAP-enabled Remote Authentication Dial-In User Service (RADIUS) server. The most widely used wired local area network. Ethernet uses carrier sense multiple access (CSMA) to allow computers to share a network and operates at 10, 100, or 1000 Mbps, depending on the physical layer used. F file server firmware A repository for files so that a local area network can share files, mail, and programs. Software that is programmed on a memory chip. G gateway GHz A device that connects two otherwise incompatible networks together. Gigahertz. One billion cycles per second. A unit of measure for frequency. OL-8371-05 Cisco Aironet 1240AG Series Access Point Hardware Installation Guide GL-3

Section	Page
Cisco Aironet 1240AG Series Access Point Hardware Installation Guide	1
Contents	3
Preface	9
Audience	9
Purpose	9
Organization	9
Conventions	10
Related Publications	12
Locating the Product Serial Number	13
Obtaining Documentation, Obtaining Support, and Security Guidelines	14
Overview	15
Product Terminology	15
Autonomous Access Points	15
Lightweight Access Points	16
Guidelines for Using Cisco Aironet Lightweight Access Points	16
Hardware Features	17
Single or Dual-Radio Operation	19
Antennas Supported	19
Ethernet Port	19
Console Port	19
LEDs	19
Power Sources	20
UL 2043 Certification	20
Anti-Theft Features	20
Network Examples with Autonomous Access Points	22
Root Access Point on a Wired LAN	23
Repeater Unit that Extends Wireless Range	24
Central Unit in an All-Wireless Network	25
Bridge Network with Wireless Clients	25
Point-to-Point Bridge Configuration	26
Workgroup Bridge Network	26
Network Example with Lightweight Access Points	27
Installing the Access Point	29
Safety Information	30
FCC Safety Compliance Statement	30
General Safety Guidelines	30
Warnings	30
Unpacking the Access Point	31
Package Contents	31
Basic Installation Guidelines	32
Controller Discovery Process for Lightweight Access Points	32
Deploying the Access Points on the Wireless Network	33
Access Point Layout and Connectors	34
Mounting Overview	35
Mounting on a Horizontal or Vertical Surface	37
Mounting Below a Suspended Ceiling	38
Mounting Above a Suspended Ceiling	39
Mounting Access Point on a Desktop or Shelf	42
Cable Security Bracket	42
Removing the Cable Security Bracket	43
Attaching the Access Point to the Mounting Plate	44
Securing the Access Point	45
Using a Security Cable	45
Securing the Access Point to the Mounting Plate	46
Connecting the Ethernet and Power Cables	48
Connecting to an Ethernet Network with an Inline Power Source	49
Connecting to an Ethernet Network with Local Power	50
Powering Up the Access Point	50
Troubleshooting 1240AG Series Autonomous Access Points	51
Checking the Autonomous Access Point LEDs	52
Checking Basic Settings	53
Default IP Address Behavior	54
Enabling the Radio Interfaces	54
SSID	54
WEP Keys	55
Security Settings	55
Low Power Condition	55
Intelligent Power Management	56
Inline Power Status Messages	57
Configuring Power Using the CLI	59
Issuing the Cisco IOS Command Using the CLI	60
Configuring the Access Point System Power Settings Using a Browser	61
Running the Carrier Busy Test	63
Running the Ping Test	64
Resetting to the Default Configuration	64
Using the MODE Button	65
Using the Web Browser Interface	65
Reloading the Access Point Image	66
Using the MODE Button	66
Web Browser Interface	67
Browser HTTP Interface	67
Browser TFTP Interface	68
Obtaining the Access Point Image File	69
Connecting to the Access Point Locally	70
Obtaining the TFTP Server Software	70
Troubleshooting 1240AG Series Lightweight Access Points	71
Guidelines for Using Cisco Aironet Lightweight Access Points	72
Using DHCP Option 43	72
Checking the Lightweight Access Point LEDs	73
Low Power Condition for Lightweight Access Points	75
Intelligent Power Management	75
Configuring Power Using Controller CLI Commands	76
Manually Configuring Controller Information Using the Access Point CLI	77
Configuring Controller Information	78
Clearing Manually Entered Controller Information	78
Manually Resetting the Access Point to Defaults	78
Returning the Lightweight Access Point to Autonomous Mode	79
Using a Controller to Return the Access Point to Autonomous Mode	79
Using the MODE Button to Return the Access Point to Autonomous Mode	79
MODE Button Setting	80
Obtaining the Autonomous Access Point Image File	80
Connecting to the Access Point Locally	81
Obtaining the TFTP Server Software	82
Translated Safety Warnings	83
Declarations of Conformity and Regulatory Information	85
Manufacturers Federal Communication Commission Declaration of Conformity Statement	86
VCCI Statement for Japan	87
Industry Canada	87
Canadian Compliance Statement	87
European Community, Switzerland, Norway, Iceland, and Liechtenstein	88
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive)	88
Declaration of Conformity for RF Exposure	91
Guidelines for Operating Cisco Aironet Access Points in Japan	92
Japanese Translation	92
English Translation	92
Administrative Rules for Cisco Aironet Access Points in Taiwan	93
Access Points with IEEE 802.11a Radios	93
Chinese Translation	93
English Translation	93
All Access Points	94
Chinese Translation	94
English Translation	94
Operation of Cisco Aironet Access Points in Brazil	95
Access Point Models	95
Regulatory Information	95
Portuguese Translation	95
English Translation	95
Declaration of Conformity Statements	96
Declaration of Conformity Statements for European Union Countries	96
Access Point Specifications	99
Channels and Maximum Power Levels	103
Console Cable Pinouts	105
Overview	106
Console Port Signals and Pinouts	106
Priming Lightweight Access Points Prior to Deployment	107
Configuring DHCP Option 43 for Lightweight Access Points	111
Overview	112
Configuring Option 43 for 1000 Series Access Points	113
Configuring Option 43 for 1100, 1130, 1200, 1240, and 1300 Series Lightweight Access Points	114
Glossary	115