Cisco WRT300N User Manual - Page 58

Application Name, Start and End Port, Protocol, To IP Address, Enabled, Save Settings

Get Cisco WRT300N PDF manuals and user guides View all Cisco WRT300N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Wireless-N Broadband Router 5. I am not able to access the Setup page of the Router's web-based utility. • Refer to "Problem #3, I want to test my Internet connection" to verify that your computer is properly connected to the Router. • Refer to "Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter" to verify that your computer has an IP Address, Subnet Mask, Gateway, and DNS. • Set a static IP address on your system; refer to "Problem #2: I need to set a static IP address." • Refer to "Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up window." 6. I need to set up a server behind my Router and make it available to the public. To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using. For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and port 110 (POP3 incoming) are used for the mail server. You can get more information by viewing the documentation provided with the server you installed. Follow these steps to set up port forwarding through the Router's web-based utility. We will be setting up web, ftp, and mail servers. 1. Access the Router's web-based utility by going to http://192.168.1.1 or the IP address of the Router. Go to the Applications & Gaming => Port Range Forwarding tab. 2. Enter any name you want to use for the Application Name. 3. Enter the Start and End Port range of the service you are using. For example, if you have a web server, you would enter the range 80 to 80. 4. Select the protocol(s) you will be using, TCP and/or UDP. 5. Enter the IP address of the PC or network device that you want the port server to go to. For example, if the web server's Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field provided. Check "Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter" for details on getting an IP address. 6. Check the Enabled option for the port services you want to use. Consider the example below: Application Name Start and End Port Protocol Web server 80 to 80 Both FTP server 21 to 21 TCP SMTP (outgoing) 25 to 25 Both POP3 (incoming) 110 to 110 Both To IP Address 192.168.1.100 192.168.1.101 192.168.1.102 192.168.1.102 Enabled X X X X When you have completed the configuration, click the Save Settings button. Appendix A: Troubleshooting 52 Common Problems and Solutions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
52
Appendix A: Troubleshooting
Common Problems and Solutions
Wireless-N Broadband Router
5.
I am not able to access the Setup page of the Router’s web-based utility.
•
Refer to “Problem #3, I want to test my Internet connection” to verify that your computer is properly
connected to the Router.
•
Refer to “Appendix E: Finding the MAC Address and IP address for Your Ethernet Adapter” to verify that
your computer has an IP Address, Subnet Mask, Gateway, and DNS.
•
Set a static IP address on your system; refer to “Problem #2: I need to set a static IP address.”
•
Refer to “Problem #10: I am a PPPoE user, and I need to remove the proxy settings or the dial-up pop-up
window.”
6.
I need to set up a server behind my Router and make it available to the public.
To use a server like a web, ftp, or mail server, you need to know the respective port numbers they are using.
For example, port 80 (HTTP) is used for web; port 21 (FTP) is used for FTP, and port 25 (SMTP outgoing) and
port 110 (POP3 incoming) are used for the mail server.
You can get more information by viewing the
documentation provided with the server you installed.
Follow these steps to set up port forwarding through the Router’s web-based utility. We will be setting up
web, ftp, and mail servers.
1.
Access the Router’s web-based utility by going to http://192.168.1.1 or the IP address of the Router.
Go to the Applications & Gaming => Port Range Forwarding tab.
2.
Enter any name you want to use for the Application Name.
3.
Enter the Start and End Port range of the service you are using. For example, if you have a web server,
you would enter the range 80 to 80.
4.
Select the protocol(s) you will be using, TCP and/or UDP.
5.
Enter the IP address of the PC or network device that you want the port server to go to. For example,
if the web server’s Ethernet adapter IP address is 192.168.1.100, you would enter 100 in the field
provided. Check “Appendix E: Finding the MAC Address and IP Address for Your Ethernet Adapter” for
details on getting an IP address.
6.
Check the
Enabled
option for the port services you want to use. Consider the example below:
When you have completed the configuration, click the
Save Settings
button.
Application Name
Start and End Port
Protocol
To IP Address
Enabled
Web server
80 to 80
Both
192.168.1.100
X
FTP server
21 to 21
TCP
192.168.1.101
X
SMTP (outgoing)
25 to 25
Both
192.168.1.102
X
POP3 (incoming)
110 to 110
Both
192.168.1.102
X