Dell Inspiron 27 7710 All-in-One Service Manual - Page 31

Steps, Next steps, Removing and installing components

Get Dell Inspiron 27 7710 All-in-One PDF manuals and user guides View all Dell Inspiron 27 7710 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

● M.2 2230 solid-state drive ● M.2 2280 solid-state drive NOTE: This procedure applies if you are installing an M.2 2230 solid-state drive. If you are replacing an M.2 2230 solid-state drive with an M.2 2280 solid-state drive, move the screw mount as shown in the following figure, before you perform the other steps in the installation procedure. The following image indicates the location of the solid-state drive and provides a visual representation of the installation procedure. Steps 1. Ensure that the thermal pad covering the M.2 2230 solid-state drive slot on the system board is in place. 2. Align the notch on the solid-state drive with the tab on the M.2 2230 solid-state drive slot. 3. Slide the solid-state drive into the M.2 solid-state drive slot on the system board. 4. Replace the screw (M2x3.5) that secures the solid-state drive to the system board. Next steps 1. Install the system-board shield. 2. Install the I/O cover. 3. Install the back cover. 4. Install the stand. 5. Follow the procedure in After working inside your computer. Removing and installing components 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
●
M.2 2230 solid-state drive
●
M.2 2280 solid-state drive
NOTE:
This procedure applies if you are installing an M.2 2230 solid-state drive.
If you are replacing an M.2 2230 solid-state drive with an M.2 2280 solid-state drive, move the screw mount as shown in the
following figure, before you perform the other steps in the installation procedure.
The following image indicates the location of the solid-state drive and provides a visual representation of the installation
procedure.
Steps
1.
Ensure that the thermal pad covering the M.2 2230 solid-state drive slot on the system board is in place.
2.
Align the notch on the solid-state drive with the tab on the M.2 2230 solid-state drive slot.
3.
Slide the solid-state drive into the M.2 solid-state drive slot on the system board.
4.
Replace the screw (M2x3.5) that secures the solid-state drive to the system board.
Next steps
1.
Install the
system-board shield
.
2.
Install the
I/O cover
.
3.
Install the
back cover
.
4.
Install the
stand
.
5.
Follow the procedure in
After working inside your computer
.
Removing and installing components
31