Dell Inspiron 27 7710 All-in-One Service Manual - Page 54

Connect the touchscreen cable to the system board.

Get Dell Inspiron 27 7710 All-in-One PDF manuals and user guides View all Dell Inspiron 27 7710 All-in-One manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Steps 1. Align the screw holes on the system board with the screw holes on the display-assembly base. 2. Replace the six screws (M3x5) that secure the system board to the display-assembly base. 3. Replace the solid-state drive screw mount (M3x4) that secures the system board to the display-assembly base. 4. Connect the display cable to the system board. 5. Connect the power-button board cable to the system board and close the latch to secure the cable. 6. Connect the media-card reader cable to the system board. 7. Connect the microphone-module cable to the system board. 8. Connect the speaker cable to the system board. 9. Connect the fan cable to the system board. 10. Connect the backlight cable to the system board. 11. Connect the camera cable to the system board. 12. Connect the touchscreen cable to the system board. NOTE: This cable is only available on computers that support touch option. Next steps 1. Install the heat sink. 2. Install the M.2 2230 solid-state drive or M.2 2280 solid-state drive. 3. Install the wireless card. 4. Install the memory module. 5. Install the system-board shield. 6. Install the I/O cover. 7. Install the back cover. 8. Install the stand. 9. Follow the procedure in After working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. 54 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Steps
1.
Align the screw holes on the system board with the screw holes on the display-assembly base.
2.
Replace the six screws (M3x5) that secure the system board to the display-assembly base.
3.
Replace the solid-state drive screw mount (M3x4) that secures the system board to the display-assembly base.
4.
Connect the display cable to the system board.
5.
Connect the power-button board cable to the system board and close the latch to secure the cable.
6.
Connect the media-card reader cable to the system board.
7.
Connect the microphone-module cable to the system board.
8.
Connect the speaker cable to the system board.
9.
Connect the fan cable to the system board.
10.
Connect the backlight cable to the system board.
11.
Connect the camera cable to the system board.
12.
Connect the touchscreen cable to the system board.
NOTE:
This cable is only available on computers that support touch option.
Next steps
1.
Install the
heat sink
.
2.
Install the
M.2 2230 solid-state drive
or
M.2 2280 solid-state drive
.
3.
Install the
wireless card
.
4.
Install the
memory module
.
5.
Install the
system-board shield
.
6.
Install the
I/O cover
.
7.
Install the
back cover
.
8.
Install the
stand
.
9.
Follow the procedure in
After working inside your computer
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
54
Removing and installing components