Dell OptiPlex GX200 Service Manual - Page 76

Microprocessor/Cooling Fan/Heat Sink Assembly

Get Dell OptiPlex GX200 PDF manuals and user guides View all Dell OptiPlex GX200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

1 Securing clips (2) To reinstall a RIMM, perform the following steps: 1. Locate the plastic securing clips at each end of the socket (see Figure 26). 2. Press the clips outward until they snap open. 3. Press the RIMM straight into the slot running down the center of the socket until the securing tabs snap into place around the ends of the RIMM. 4. Replace the computer cover. 5. Reset the chassis intrusion detector. Figure 26. RIMM Installation 1 Securing clips (2) 2 Notches (2) 6. Run the Dell Diagnostics to verify that the RIMMs are operating properly. Microprocessor/Cooling Fan/Heat Sink Assembly Figure 27. Microprocessor/Cooling Fan/Heat Sink Assembly 1 Cooling fan/heat sink assembly 2 ZIF socket 3 Retaining clip CAUTION: The microprocessor/heat sink assembly can get extremely hot. Be sure that the assembly has had sufficient time to cool before you touch it. NOTE: Dell recommends that only a technically knowledgeable person perform this procedure. To replace a microprocessor, perform the following steps:

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
To reinstall a RIMM, perform the following steps:
1.
Locate the plastic securing clips at each end of the socket (see
Figure 2
6
).
2.
Press the clips outward until they snap open.
3.
Press the RIMM straight into the slot running down the center of the socket until the securing tabs snap into place around the ends of the
RIMM.
4.
Replace the computer cover
.
5.
Reset the chassis intrusion detector
.
Figure 26. RIMM Installation
6.
Run the Dell Diagnostics to verify that the RIMMs are operating properly.
Microprocessor/Cooling Fan/Heat Sink Assembly
Figure 27. Microprocessor/Cooling Fan/Heat Sink Assembly
To replace a microprocessor, perform the following steps:
1
Securing clips (2)
1
Securing clips (2)
2
Notches (2)
1
Cooling fan/heat sink assembly
2
ZIF socket
3
Retaining clip
CAUTION: The microprocessor/heat sink assembly can get extremely hot. Be sure that the assembly has had sufficient time to
cool before you touch it.
NOTE
:
Dell recommends that only a technically knowledgeable person perform this procedure.