Dell PowerConnect 5324 User's Guide Addendum - Page 5

Configuring LLDP Using CLI Commands, interface ethernet g, lldp enable - mib

Get Dell PowerConnect 5324 PDF manuals and user guides View all Dell PowerConnect 5324 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

Updates Interval (5-32768) - Indicates that rate at which LLDP advertisement updates are sent. The possible field range is 5 - 32768 seconds. The default value is 30 seconds. Hold Time (2-10) - Indicates the amount of time that LLDP packets are held before the packets are discarded. The possible field range is 2 - 10 seconds. The field default is 4 seconds. Reinitializing Delay (1-10) - Indicates the amount of time that passes between disabling LLDP and when reinitializing begins. The possible field range is 1 - 10 seconds. The field default is 2 seconds. Transmit Delay (1-8192) - Indicates the amount of time that passes between successive LLDP frame transmissions due to changes in the LLDP local systems MIB. The possible field value is 1 - 8192 seconds. The field default is 2 seconds. Configuring LLDP Using CLI Commands Table 1-1. LLDP Properties CLI Commands CLI Command lldp enable (global) lldp hold-multiplier number lldp reinit-delay Seconds lldp tx-delay Seconds Description Enables enable Link Layer Discovery Protocol. Specifies the time that the receiving device should hold a Link Layer Discovery Protocol (LLDP) packet before discarding it. Specifies the minimum time an LLDP port will wait before reinitializing. Specifies the delay between successive LLDP frame tr.ansmissions. The following is an example of the CLI commands: Console(config)# interface ethernet g5 Console(config-if)# lldp enable 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
5
Updates Interval (5-32768) —
Indicates that rate at which LLDP advertisement updates are sent. The
possible field range is 5 - 32768 seconds. The default value is 30 seconds.
Hold Time (2-10) —
Indicates the amount of time that LLDP packets are held before the packets are dis-
carded. The possible field range is 2 - 10 seconds. The field default is 4 seconds.
Reinitializing Delay
(1-10)
— Indicates the amount of time that passes between disabling LLDP and when
reinitializing begins. The possible field range is 1 - 10 seconds. The field default is 2 seconds.
Transmit Delay (1-8192)
— Indicates the amount of time that passes between successive LLDP frame trans-
missions due to changes in the LLDP local systems MIB. The possible field value is
1 – 8192 seconds. The field default is 2 seconds.
Configuring LLDP Using CLI Commands
The following is an example of the CLI commands:
Table 1-1.
LLDP Properties CLI Commands
CLI Command
Description
lldp enable (global)
Enables enable Link Layer Discovery
Protocol.
lldp hold-multiplier
number
Specifies the time that the receiving
device should hold a Link Layer
Discovery Protocol (LLDP) packet
before discarding it.
lldp reinit-delay
Seconds
Specifies the minimum time an LLDP
port will wait before reinitializing.
lldp tx-delay
Seconds
Specifies the delay between successive
LLDP frame tr.ansmissions.
Console(config)#
interface ethernet g
5
Console(config-if)#
lldp enable