Dell PowerStore 3200T EMC PowerStore Installation and Service Guide for PowerS - Page 35

Cable the base enclosure to the NVMe expansion enclosure, Prerequisites, Steps

Page 35 highlights

a. On the left-hand side of the rear of the cabinet, align the two retention latches with the two upper rail clips, and insert them into the clips until you feel and hear an audible click. Figure 27. Installing the cable management arms Cable the base enclosure to the NVMe expansion enclosure Prerequisites Determine how many expansion enclosures you are installing. Use the cable label diagrams that shipped with your system to determine the end-to-end locations for the back-end cables. NOTE: If you are installing more than one NVMe expansion enclosure, use the 2M cables (PN 038-004-928-00) to connect the base enclosure to the NVMe expansion enclosure. Use the 2.5M cables (PN 038-004-986-00) to connect an NVMe expansion enclosure to another NVMe expansion enclosure. Steps 1. Apply the provided cable labels to each end of the cables. NOTE: The system ships with three sheets of labels. All three sheets contain the same information. They are just different colors. You only need to use one label sheet per expansion enclosure. The different colors are to identify which expansion enclosure the cables belong to. For example, you could use the pink label sheet for the first enclosure, and then use the green sheet for the second enclosure. 2. Ensure that the cable management arms (CMAs) are fully open and in the service position. 3. Open the CMA baskets and loosen the velcro straps. 4. Based on the following illustrations, route the data cables through the CMAs. The cables represented by yellow lines route through the upper CMA, and the cables represented by blue lines route through the lower CMA. Follow these guidelines when routing cables: ● Gently route the cables into and around the arms without excess bending. ● Ensure that the data cables are oriented correctly to latch into the ports. Install a new base enclosure and optional expansion enclosure 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191

a.
On the left-hand side of the rear of the cabinet, align the two retention latches with the two upper rail clips, and insert
them into the clips until you feel and hear an audible click.
Figure 27. Installing the cable management arms
Cable the base enclosure to the NVMe expansion enclosure
Prerequisites
Determine how many expansion enclosures you are installing. Use the cable label diagrams that shipped with your system to
determine the end-to-end locations for the back-end cables.
NOTE:
If you are installing more than one NVMe expansion enclosure, use the 2M cables (PN 038-004-928-00) to connect
the base enclosure to the NVMe expansion enclosure. Use the 2.5M cables (PN 038-004-986-00) to connect an NVMe
expansion enclosure to another NVMe expansion enclosure.
Steps
1.
Apply the provided cable labels to each end of the cables.
NOTE:
The system ships with three sheets of labels. All three sheets contain the same information. They are just
different colors. You only need to use one label sheet per expansion enclosure. The different colors are to identify which
expansion enclosure the cables belong to. For example, you could use the pink label sheet for the first enclosure, and
then use the green sheet for the second enclosure.
2.
Ensure that the cable management arms (CMAs) are fully open and in the service position.
3.
Open the CMA baskets and loosen the velcro straps.
4.
Based on the following illustrations, route the data cables through the CMAs. The cables represented by yellow lines route
through the upper CMA, and the cables represented by blue lines route through the lower CMA.
Follow these guidelines when routing cables:
Gently route the cables into and around the arms without excess bending.
Ensure that the data cables are oriented correctly to latch into the ports.
Install a new base enclosure and optional expansion enclosure
35