Dell PowerStore 3200T EMC PowerStore Installation and Service Guide for PowerS - Page 54
Install a 2.5\, Pushing the latch cover up, Removing a 2.5 drive
View all Dell PowerStore 3200T manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 54 highlights
Figure 47. Pushing the latch cover up 3. Push down the orange button to release the latch. 4. Remove the drive from the slot. Figure 48. Removing a 2.5" drive 5. Place the drive on a static-free surface. Install a 2.5" drive About this task CAUTION: If you are installing multiple drives in a system that is powered up, wait one to two minutes before sliding the next drive into position. Steps 1. Align the drive with the guides in the slot. 2. With the latch fully opened, gently push the drive into the slot. The latch begins to rotate downward when it meets the enclosure. 3. Push the orange button until the drive is fully seated in the slot. 4. Push the latch down until it locks into place. 54 Base enclosure service procedures
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
Figure 47. Pushing the latch cover up
3.
Push down the orange button to release the latch.
4.
Remove the drive from the slot.
Figure 48. Removing a 2.5" drive
5.
Place the drive on a static-free surface.
Install a 2.5" drive
About this task
CAUTION:
If you are installing multiple drives in a system that is powered up, wait one to two minutes before
sliding the next drive into position.
Steps
1.
Align the drive with the guides in the slot.
2.
With the latch fully opened, gently push the drive into the slot.
The latch begins to rotate downward when it meets the enclosure.
3.
Push the orange button until the drive is fully seated in the slot.
4.
Push the latch down until it locks into place.
54
Base enclosure service procedures