Dell PowerStore 3200T EMC PowerStore Installation and Service Guide for PowerS - Page 62

Replace an embedded module, Before you begin

Page 62 highlights

2. Ship the failed part to your service provider as described in the instructions that were included with the replacement part. 3. For more information about returning customer-replaceable parts: a. Open PowerStore Manager. b. Click Settings on the upper right of the screen. c. Click General Support. d. Under Drives, Power Supplies, and Other Parts, click Return Part. e. If your screen does not show the Return Part link, contact your service provider for instructions. Replace an embedded module Take the following actions to remove the faulted embedded module and install the replacement embedded module into the system. Before you begin CAUTION: Before starting this procedure, use the PowerStore Manager Hardware view and Alerts view to verify that the appliance and peer node are healthy with no outstanding alerts. If multiple nodes need to be removed while performing this procedure, repeat this verification for each affected node before proceeding to remove the next node. If necessary, contact your service provider before starting the replacement procedure. Identify a faulted embedded module from PowerStore Manager Before you replace an embedded module, ensure that you have identified its location within the system. Using PowerStore Manager, you can identify and locate a faulted embedded module. Steps 1. From PowerStore Manager, select Hardware. 2. Select the appliance that includes the embedded module that you need to replace. 3. On the Components card, under Rear View, expand BaseEnclosure. 4. Expand the node that includes the embedded module, and then select EmbeddedModule. Faulted parts appear in red in the image of the system, and report a status of Faulted in the State field. Embedded module LEDs Use the fault LEDs to identify the faulted part. Figure 57. Embedded module LEDs Table 4. Embedded module LEDs LED Unsafe to remove Location State White 62 Base enclosure service procedures Description Do not remove the node. Improper removal could cause data loss.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191

2.
Ship the failed part to your service provider as described in the instructions that were included with the replacement part.
3.
For more information about returning customer-replaceable parts:
a.
Open PowerStore Manager.
b.
Click
Settings
on the upper right of the screen.
c.
Click
General Support
.
d.
Under
Drives, Power Supplies, and Other Parts
, click
Return Part
.
e.
If your screen does not show the Return Part link, contact your service provider for instructions.
Replace an embedded module
Take the following actions to remove the faulted embedded module and install the replacement embedded module into the
system.
Before you begin
CAUTION:
Before starting this procedure, use the PowerStore Manager Hardware view and Alerts view to verify
that the appliance and peer node are healthy with no outstanding alerts. If multiple nodes need to be removed
while performing this procedure, repeat this verification for each affected node before proceeding to remove
the next node. If necessary, contact your service provider before starting the replacement procedure.
Identify a faulted embedded module from PowerStore Manager
Before you replace an embedded module, ensure that you have identified its location within the system. Using PowerStore
Manager, you can identify and locate a faulted embedded module.
Steps
1.
From PowerStore Manager, select
Hardware
.
2.
Select the appliance that includes the embedded module that you need to replace.
3.
On the
Components
card, under
Rear View
, expand
BaseEnclosure
.
4.
Expand the node that includes the embedded module, and then select
EmbeddedModule
.
Faulted parts appear in red in the image of the system, and report a status of
Faulted
in the
State
field.
Embedded module LEDs
Use the fault LEDs to identify the faulted part.
Figure 57. Embedded module LEDs
Table 4. Embedded module LEDs
LED
Location
State
Description
Unsafe to remove
White
Do not remove the node. Improper
removal could cause data loss.
62
Base enclosure service procedures