Denon AVR 1906 Owners Manual - Page 12

Cursor, Setup - channel

Get Denon AVR 1906 - AV Receiver PDF manuals and user guides
UPC - 081757506557
View all Denon AVR 1906 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

ENGLISH Easy Setup and Operation Starting Auto Setup 1 Press the SETUP button. • The "System Setup" menu appears. 4 Press the CURSOR D or H button to select "Start", then press the CURSOR F button. • Start the measurements. Easy Setup and Operation • Measurement is cancelled if the MASTER VOLUME control knob is operated while the Auto Setup is performed. • If the output volume and crossover frequency of your subwoofer speaker can be changed, then set the volume to halfway and the crossover filter to maximum or switch off the low-pass filter. 2 Press the CURSOR D or H button to select "Auto Setup", then press the ENTER button. • The "Auto Setup" screen appears. 3 Press the CURSOR D or H button to select "Power Amp Assign", then press the CURSOR F or G button to select "S. Back", "ZONE2" or "Bi-Amp". Measurement of each channel is performed as follows: 1 FL FR 2 3 C SW SL SR SBL SBR 1: Only the front speakers (A) are measured, front speakers (B) are not available. Even if the front speakers (B) are set, the setting automatically switches to the front speakers (A) once measurements are completed. 2: The subwoofer speaker is measured twice. 3: When "ZONE2" and "Bi-Amp" are selected, these are not displayed. After each channel is measured, "Calculating" appears. The display switches to the Auto Setup check screen automatically. 2 About automatic retry To confirm the results of the measurements, remeasurement is automatically performed. Remeasurement is performed up to 2 times. During this time, "Retry1" or "Retry2" is displayed on the screen. NOTE: • When measurements have been made using the measurement microphone, speakers with built-in filters, such as a subwoofer, might be set to a value that differs from the physical distance because of the internal electrical delay. When "S. Back" is selected, the test tone during Auto Setup will be output from the surround back speaker. When "ZONE2" is selected, change the setting to "ZONE2". The test tone during Auto Setup is set so that it will not be output to ZONE2 (Another room). When "Bi-Amp" is selected, change the setting to "BiAmp". The test tone during Auto Setup is set so that it will be output from the Bi-Amp speaker. 9 ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
ENGLISH
9
Easy Setup and Operation
Easy Setup and Operation
ENGLISH
Starting Auto Setup
2
Press the
CURSOR
D
or
H
button to select “Auto
Setup”, then press the
ENTER
button.
• The “Auto Setup” screen appears.
1
Press the
SETUP
button.
• The “System Setup” menu appears.
Measurement of each channel is performed as follows:
4
Press the
CURSOR
D
or
H
button to select
“Start”, then press the
CURSOR
F
button.
• Start the measurements.
FL
FR
C
SW
SL
SR
SBL
SBR
1
2
3
1:
Only the front speakers (A) are measured, front speakers
(B) are not available. Even if the front speakers (B) are
set, the setting automatically switches to the front
speakers (A) once measurements are completed.
2: The subwoofer speaker is measured twice.
3: When “ZONE2” and “Bi-Amp” are selected, these are
not displayed.
After each channel is measured, “Calculating” appears.
The display switches to the Auto Setup check screen
automatically.
• Measurement is cancelled if the
MASTER VOLUME
control knob
is operated while the Auto Setup is performed.
•
If the output volume and crossover frequency of your
subwoofer speaker can be changed, then set the volume to
halfway and the crossover filter to maximum or switch off
the low-pass filter.
2
About automatic retry
To confirm the results of the measurements, remeasurement is
automatically performed.
Remeasurement is performed up to 2 times. During this time,
“Retry1” or “Retry2” is displayed on the screen.
NOTE:
• When measurements have been made using the
measurement microphone, speakers with built-in filters,
such as a subwoofer, might be set to a value that differs
from the physical distance because of the internal electrical
delay.
When “S. Back” is selected, the test tone during Auto
Setup will be output from the surround back speaker.
When “ZONE2” is selected, change the setting to
“ZONE2”. The test tone during Auto Setup is set so that it
will not be output to ZONE2 (Another room).
When “Bi-Amp” is selected, change the setting to “Bi-
Amp”. The test tone during Auto Setup is set so that it will
be output from the Bi-Amp speaker.
3
Press the
CURSOR
D
or
H
button to select
“Power Amp Assign”, then press the
CURSOR
F
or
G
button to select “S. Back”, “ZONE2” or
“Bi-Amp”.