Denon AVR-3805 Owners Manual - Page 57

System call

Get Denon AVR-3805 PDF manuals and user guides
UPC - 081757505987
View all Denon AVR-3805 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

System call The accessorious remote control unit is equipped with "system call" function allowing a series of remote control signals to be transmitted by pressing a single button. This function can be used for example to turn on the amplifier's power, select the input source, turn on the monitor TV's power, turn on the source component's power and set the source to the play mode, all at a signal button. (1) System call buttons Up to 12 signals each can be stored at the "CALL1" ~ "CALL6" buttons. The System Call function can be used in the "AMP", "ZONE2", and "ZONE3" modes. 1 (2) Storing system call signals 1 Press the power ON button and the OFF button at the same time. 3, 5 2, 6 2 Press the "3" button to select system call setting. 3, 7 3 Press the Mode button for the component you want to register at the system call button, then press the ENTER button. CH SEL ENTER 4 Press the button you want to register. 5 The mode can be switched by pressing a mode button. 6 Repeat steps 4 and 5 to register the desired buttons. Up to 12 signals each can be stored at the CALL1~CALL6. 7 Press the ENTER button after the button registration is completed. There will be a changeover to the System Call registration screen. 8 Press buttons from "CALL 1" to "CALL 6" to register the System Call. • "OK" is displayed and the set returns to the normal operating mode. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
57
System call
(1) System call buttons
Up to 12 signals each can be stored at
the “CALL1” ~ “CALL6” buttons.
The System Call function can be used
in
the
“AMP”,
“ZONE2”,
and
“ZONE3” modes.
(2) Storing system call signals
1
2
5
Press the power ON button and the OFF button at the same
time.
Press the “3” button to select system call setting.
The mode can be switched by pressing a mode button.
3, 5
3, 7
1
2, 6
The accessorious remote control unit is equipped with “system call” function allowing a series of remote control signals to be transmitted by
pressing a single button.
This function can be used for example to turn on the amplifier’s power, select the input source, turn on the monitor TV’s power, turn on the source
component’s power and set the source to the play mode, all at a signal button.
3
4
Press the button you want to register.
6
Repeat steps 4 and 5 to register the desired buttons.
Up to 12 signals each can be stored at the CALL1~CALL6.
7
Press the ENTER button after the button registration is
completed. There will be a changeover to the System Call
registration screen.
Press the Mode button for the component you want to
register at the system call button, then press the ENTER
button.
8
Press buttons from “CALL 1” to “CALL 6” to register the
System Call.
• “OK” is displayed and the set returns to the normal
operating mode.
CH SEL
ENTER