Denon AVR-791 Owners Manual - English - Page 58

Simple version Basic version Advanced version ENGLISH HDMI Setup Default settings are underlined. Make settings for HDMI video/audio output. Setting items Setting details Auto Lip Sync Make automatic compensation for timing shift in audio and video output. ON : Compensated. OFF : Not compensated. HDMI Audio Out Select HDMI audio output device. Amp : Play back through speakers connected to the receiver. TV : Play back through TV connected to the receiver. When the HDMI control function is activated, priority is given to the TV audio setting (vpage 34 "HDMI control function"). HDMI Control You can link operations with devices connected to HDMI and compatible with HDMI Control. ON : Use HDMI control function. OFF : Do not use HDMI control function. • When a device that is not compatible with the HDMI control function is connected, set "HDMI Control" to "OFF". • Please consult the operating instructions for each connected component to check the settings. • Refer to "HDMI control function" (vpage 34) for more information about the HDMI control function. NOTE • When "HDMI Control" is set to "ON", it consumes more standby power. If you are not using this unit for an extended period, it is recommended that you unplug the power cord from the power outlet. • "HDMI Control" does not work when the power to the equipment is off. Either turn power on or set to standby. • The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control. • If the "HDMI Control" settings have been changed, always reset the power to connected devices after the change. Standby Source Sets the HDMI input source to put into standby when the power is on. Last : This item is set at the last-used input source. HDMI1 / HDMI2 / HDMI3 / HDMI4 : Put the respective input source into standby. "Standby Source" can be set when "HDMI Control" is set to "ON". Power Off Control Links the power standby of this unit to external equipment. All : If power to a connected TV is turned off independently of the input source, power to this unit is automatically set to standby. Video : If power to a connected TV is turned off when the input source is BD / DVD / TV / SAT/CBL / GAME / V.AUX / DOCK, power to this unit is automatically set to standby. OFF : This unit does not link with power to a TV. "Power Off Control" can be set when "HDMI Control" is set to "ON". Manual Setup Audio Setup Default settings are underlined. Make settings for audio playback. Setting items 2ch DIRECT/STEREO Select the method for setting the speakers used in the 2-channel direct and stereo playback modes. Setting details Setting : Select the method for setting the speakers used in the 2-channel direct and stereo playback modes. • Basic : The settings at "Speaker Setup" (vpage 52) are applied. • Custom : Make separate settings for 2-channel. Make the following settings: Front : Set the front speaker size. • Large : Use a large speaker that can adequately play back low frequencies. • Small : Use a small speaker that has inadequate playback capacity for low frequencies. If "Speaker Config." - "Subwoofer" (vpage 52) is set to "No", the setting is automatically set to "Large". Subwoofer : Set the presence of a subwoofer. • Yes : Use a subwoofer. • No : Select when a subwoofer is not connected. If "Speaker Config." - "Subwoofer" (vpage 52) is set to "No", the setting is automatically set to "No". If the "Front" setting is "Small", the setting is automatically "Yes". Subwoofer Mode : Select low range signals to be reproduced by subwoofer. • LFE : When the "2ch DIRECT/STEREO" - "Front" setting is set to "Large", the LFE signal alone is output from the subwoofer. Also, when the "2ch DIRECT/STEREO" - "Front" setting is set to "Small", the front channel low range signal is added to the LFE signal output from the subwoofer. • LFE+Main : The front channel low range signal is added to the LFE signal output from the subwoofer. This setting can be set made "2ch DIRECT/STEREO" - "Subwoofer" is set to "Yes". Crossover : Set the maximum frequency of the bass signal output from each channel to the subwoofer. • 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz • This setting can be set made "2ch DIRECT/STEREO" - "Subwoofer" is set to "Yes". • If the "2ch DIRECT/STEREO" - "Front" setting is "Large" and the "Subwoofer Mode" setting is "LFE", "Full Band" is displayed and the setting cannot be made. Information Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu 55