Epson BrightLink 1480Fi Installation Guide - Page 78

Do not place anything other than the markers near the projected image during angle

Get Epson BrightLink 1480Fi PDF manuals and user guides View all Epson BrightLink 1480Fi manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

6. Attach the two markers to the positions shown on the projected screen. Match the positions so that the crosses ( ) overlap with the points ( ) on the marker positions. Move the marker over the projected cross until the lines of the cross align with the lines on the marker. Attach the markers to the projection screen as follows: • For magnetic screens: Place the bottom of the markers onto the screen with the thinner end of the marker facing the touch unit. • For non-magnetic screens: Use the supplied tape to secure the markers with the thinner side of the marker facing the touch unit. Do not place anything other than the markers near the projected image during angle adjustment. If other objects are on the projected image, angle adjustment may not be performed correctly. 7. Press the [Enter] button on the remote control or control panel to begin the auto adjustment. 8. When adjustments are complete, remove the markers. If auto adjustment fails, follow the instructions on the screen to manually adjust the angle of the laser and run auto adjustment again. 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
78
6.
Attach the two markers to the positions shown on the projected screen.
Match the positions so that the crosses (
) overlap with the points (
) on the marker positions.
Move the marker over the projected cross until the lines of the cross align with the lines on the marker.
Attach the markers to the projection screen as follows:
•
For magnetic screens: Place the bottom of the markers onto the screen with the thinner end of the
marker facing the touch unit.
•
For non-magnetic screens: Use the supplied tape to secure the markers with the thinner side of the
marker facing the touch unit.
7.
Press the [Enter] button on the remote control or control panel to begin the auto adjustment.
8.
When adjustments are complete, remove the markers.
Do not place anything other than the markers near the projected image during angle
adjustment. If other objects are on the projected image, angle adjustment may not be
performed correctly.
If auto adjustment fails, follow the instructions on the screen to manually adjust the
angle of the laser and run auto adjustment again.