Home » Epson Manuals » Label Makers » Epson ColorWorks CW-C6500A » Manual Viewer

Epson ColorWorks CW-C6500A Technical Reference Guide - External I/O CW-C6000/C - Page 56

of Jumper Settings and I/O Power Supply and Ground Connections

View all Epson ColorWorks CW-C6500A manuals

Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Figure of Jumper Settings and I/O Power Supply and Ground Connections Depending on the usage environment at the customer place, the structure allows the I/O power supply (VCC_EX) and Signal Ground (SG) to be separated from the Frame Ground (FG). The following describes the jumper settings and I/O power supply and ground connections. State CN100 JP setting CN200 JP setting Power supply/SG not separated 1-2 pin shorted 1-2 pin shorted Power supply/SG separated 2-3 pin shorted 2-3 pin shorted c • When shorting pins 1 and 2 on CN100, DO NOT short pins 2 and 3 on CN200. IMPORTANT • When shorting pins 2 and 3 on CN100, DO NOT short pins 1 and 2 on CN200. Q NOTE When separating the power supply and signal ground, do not provide a 5 V power supply to an external device. I/O power supply/SG not separated Printer side +5 V CN200 VCC_EX 1 2 3 NON CONNECTION CN100 1 2 3 NON CONNECTION FG SG External device side SG 56

Section	Page
Restriction of Use	3
About this Manual	3
Aim of the Manual	3
Manual Content	3
Key to Symbols	4
Safety Precautions on Handling	4
Contents	5
Overview	7
Functionality	7
External device	8
External I/O Specification	9
Connector	9
Signal Definitions	9
Pulse signal	9
Level signal	10
Pin Assignment and Specification for I/O Signals	11
Specification for I/O Signals	15
Commands	17
List of Commands	17
Setting Commands	21
End print signal (output) mode settings	21
Mode setting for data ready signal (output)	23
Mode setting for clogged nozzle detected signal (output)	24
Mode setting for head maintenance signal (output)	25
Mode setting for printer ready signal (output)	26
Mode setting for warning signal (output)	27
Mode setting for error signal (output)	28
Ink low signal (output) mode setting	29
Ink cartridge exchange signal (output) mode setting	30
Paper out signal (output) mode setting	31
Mode setting for pause signal (input)	32
Mode setting for head cleaning signal (input)	33
Mode setting for clogged nozzle check signal (input)	34
Mode setting for feed signal (input)	35
Mode setting for start print signal (input)	36
Mode setting for re-print signal (input)	37
Acquisition Commands for Setting Values	38
Acquisition commands for mode setting values for end print signal (output)	38
Acquisition commands for mode setting values for data ready signal (output)	38
Acquisition commands for mode setting values for clogged nozzle detected signal (output)	39
Acquisition commands for mode setting values for head maintenance signal (output)	39
Acquisition commands for mode setting values for printer ready signal (output)	40
Acquisition commands for mode setting values for warning signal (output)	40
Acquisition commands for mode setting values for error signal (output)	40
Acquisition of mode setting value for ink low signal (input)	41
Acquisition of mode setting value for ink cartridge exchange signal (input)	41
Acquisition command of mode setting value for paper out signal (input)	42
Acquisition commands for mode setting values for pause signal (input)	42
Acquisition commands for mode setting values for head cleaning signal (input)	43
Acquisition commands for mode setting values for clogged nozzle check signal (input)	43
Acquisition commands for mode setting values for feed signal (input)	43
Acquisition commands for mode setting values for start print signal (input)	44
Acquisition commands for mode setting values for re-print signal (input)	44
Printer Statuses and Signals	45
Timing	47
Basic Timing for Label Printing	47
Basic Timing for Pausing	48
Basic Timing for Label Feeding	49
When \	49
When \	49
Basic Timing for Nozzle Check and Head Cleaning	50
Settings on the Printer	53
End Print Signal Mode Settings	53
Mode Setting for Start Print Signal	53
Mode Setting for Re-print Signal	54
Appendix	55
Cautions for Setting Jumpers	55
Figure of Jumper Settings and I/O Power Supply and Ground Connections	56
I/O signal specifications when I/O power supply and SG are separated	57