HealthRider 230 English Manual - Page 16

Seat Assembly

Get HealthRider 230 PDF manuals and user guides View all HealthRider 230 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

40. Important: Follow all three Cables from end to 40 end and make sure they rest in the grooves of all Pulleys and that both the Cables and the Pulleys move smoothly. Attach the bolt at the end of the Low Cable (72), the 1/2Ó Plain Nut (68), the 1 1/2Ó Flat Washer (48) and the Adjustment Tube (89) to the Weight Tube (17) in the order shown. Note: The bolt at the end of the Low Cable is one of the means for tightening the Cables (72, 73 and 92). Thread the bolt into the Weight Tube until all Cables are tight and rest firmly in the grooves of all Pulleys. Then tighten the 1/2Ó Plain Nut (68) onto the 1 1/2Ó Washer (48). Insert the Weight Pin (19) into one of the holes between the Weights (21). 41 Seat Assembly 41. Locate and open the parts bag labeled ÒSeat 47 Assembly.Ó 72 68 48 89 17 19 21 98 38 50 51 39 Press a 1 1/4Ó Square Inner Cap (98) into the indicated end of the Backrest Center Tube (38). Attach the Backrest Center Tube to the bracket on the Seat Frame (7) with a 3/8Ó x 2 3/4Ó Bolt (47) and a 3/8Ó Nylon Locknut (50). Slide the Backrest Adjustment Tube (39) onto the Backrest Center Tube (38). If necessary, pull out the Short Adjustment Knob (51). 42. Press a 1Ó x 1 1/2Ó Inner Cap (96) into each end of both Backrest Frames (37). Identify the Right Backrest Frame (101) and the Left Backrest Frame (37) by looking at the welded bushings. Orient the Backrest Frames so the welded bushings are facing the Seat Frame (7) and are on the lower edge of the Backrest Frames. Attach the Backrest Frames (37, 101) to the indicated hole in the Seat Frame (7) with a 3/8Ó x 6 1/2Ó Bolt (65) and a 3/8Ó Nylon Locknut (50). Attach the Backrest Frames (37) to the indicated hole in the Backrest Adjustment Tube (39) with a 3/8Ó x 6 1/2Ó Bolt (65) and a 3/8Ó Nylon Locknut (50). 43. Attach the Backrest (12) to the Backrest Frames (37) with four 1/4Ó x 2Ó Bolts (74) and four 1/4Ó Flat Washers (71). Attach the Seat (13) to the brackets on the Seat Frame (7) with four 1/4 x 3/4Ó Bolts (49). 7 Bracket 42 96 37 Welded Bushings 65 101 65 39 50 43 37 71 96 7 12 13 71 7 74 74 49 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
16
40
21
19
17
89
48
68
40.
Important: Follow all three Cables from end to
end and make sure they rest in the grooves of all
Pulleys and that both the Cables and the Pulleys
move smoothly.
Attach the bolt at the end of the Low
Cable (72), the 1/2± Plain Nut (68), the 1 1/2± Flat
Washer (48) and the Adjustment Tube (89) to the
Weight Tube (17) in the order shown.
Note: The bolt
at the end of the Low Cable is one of the means
for tightening the Cables (72, 73 and 92). Thread
the bolt into the Weight Tube until all Cables are
tight and rest firmly in the grooves of all Pulleys.
Then tighten the 1/2² Plain Nut (68) onto the 1
1/2² Washer (48).
Insert the Weight Pin (19) into one of the holes
between the Weights (21).
42
65
65
39
50
96
7
37
101
Welded Bushings
96
42.
Press a 1± x 1 1/2± Inner Cap (96) into each end of
both Backrest Frames (37).
Identify the Right Backrest Frame (101) and the Left
Backrest Frame (37) by looking at the welded bush-
ings. Orient the Backrest Frames so the welded bush-
ings are facing the Seat Frame (7) and are on the
lower edge of the Backrest Frames. Attach the
Backrest Frames (37, 101) to the indicated hole in the
Seat Frame (7) with a 3/8± x 6 1/2± Bolt (65) and a
3/8± Nylon Locknut (50).
Attach the Backrest Frames (37) to the indicated hole
in the Backrest Adjustment Tube (39) with a
3/8± x 6 1/2± Bolt (65) and a 3/8± Nylon Locknut (50).
43
7
74
74
12
71
13
37
71
49
43.
Attach the Backrest (12) to the Backrest Frames (37)
with four 1/4± x 2± Bolts (74) and four 1/4± Flat
Washers (71).
Attach the Seat (13) to the brackets on the Seat
Frame (7) with four 1/4 x 3/4± Bolts (49).
41
Bracket
47
7
39
51
38
98
50
41.
Locate and open the parts bag labeled ±Seat
Assembly.²
Press a 1 1/4± Square Inner Cap (98) into the indicat-
ed end of the Backrest Center Tube (38). Attach the
Backrest Center Tube to the bracket on the Seat
Frame (7) with a 3/8± x 2 3/4± Bolt (47) and a 3/8±
Nylon Locknut (50). Slide the Backrest Adjustment
Tube (39) onto the Backrest Center Tube (38).
If nec-
essary, pull out the Short Adjustment Knob (51).
Seat Assembly
72