HP 166207-B21 Smart Array 5300 Controller User Guide - Page 139

Slot x Drive Array Recovery Needed., Automatic Data Recovery: SCSI port

Get HP 166207-B21 - Smart Array 5302/32 RAID Controller PDF manuals and user guides
UPC - 720591292225
View all HP 166207-B21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 139 highlights

POST Error Messages Table G-1: POST Error Messages continued Message Description 1786 Slot x Drive Array Recovery Needed. The following SCSI drive(s) need Automatic Data Recovery: SCSI port (y): SCSI ID (x) Select F1 to continue with recovery of data to drive(s). Select F2 to continue without recovery of data to drive(s). -or- Slot x drive array recovery needed. Automatic Data Recovery previously aborted! The following SCSI drive(s) need Automatic Data Recovery (rebuild): SCSI port (y): SCSI ID (x) Select F1 to retry Automatic Data Recovery to drive. Select F2 to continue without starting Automatic Data Recovery. 1787 Slot x drive array operating in Interim Recovery Mode. The following SCSI drive(s) should be replaced: SCSI port (y): SCSI ID (x) Meaning and Recommended Action The message normally appears when a drive is replaced in a fault-tolerant configuration when the system is powered down. In this case, press the F1 key to start the automatic data recovery process. A 1786 POST message will appear if the previous rebuild attempt was aborted for any reason. Run the Array Diagnostics Utility (ADU) for more information. If the replacement drive was failed, try using another replacement drive. If rebuild was aborted due to a read error from another physical drive in the array: 1. Back up all readable data on the array. 2. Run Diagnostics Surface Analysis. 3. Restore your data. Following a system restart, this message reminds you that drive x is defective and fault tolerance is being used. Replace drive x as soon as possible. A loose or defective cable may also cause this error. continued Compaq Smart Array 5300 Controller User Guide G-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
POST Error Messages
Compaq Smart Array 5300 Controller User Guide
G-9
Table G-1:
POST Error Messages
continued
Message
Description
Meaning and Recommended Action
1786
Slot x Drive Array Recovery Needed.
The following SCSI drive(s) need
Automatic Data Recovery: SCSI port
(
y
): SCSI ID (
x
)
Select
F1
to continue with recovery of
data to drive(s)
.
Select
F2
to continue
without recovery of data to drive(s)
.
-or-
Slot x drive array recovery needed.
Automatic Data Recovery previously
aborted! The following SCSI drive(s)
need Automatic Data Recovery
(rebuild):
SCSI port (
y
): SCSI ID (
x
)
Select
F1
to retry Automatic Data
Recovery to drive
.
Select
F2
to
continue without starting Automatic
Data Recovery.
The message normally appears when a
drive is replaced in a fault-tolerant
configuration when the system is powered
down. In this case, press the
F1
key to start
the automatic data recovery process.
A 1786 POST message will appear if the
previous rebuild attempt was aborted for
any reason. Run the Array Diagnostics
Utility (ADU) for more information. If the
replacement drive was failed, try using
another replacement drive. If rebuild was
aborted due to a read error from another
physical drive in the array:
1.
Back up all readable data on the array.
2.
Run Diagnostics Surface Analysis.
3.
Restore your data.
1787
Slot x drive array operating in Interim
Recovery Mode. The following SCSI
drive(s) should be replaced:
SCSI port (y): SCSI ID (x)
Following a system restart, this message
reminds you that drive
x
is defective and
fault tolerance is being used. Replace drive
x
as soon as possible. A loose or defective
cable may also cause this error.
continued