HP 6125G HP 6125-CMW520-R2106 Release Notes - Page 25

Modifying serial port parameters

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2. Press Ctrl + D within four seconds after the "Press Ctrl+D to access BASIC BOOT MENU" prompt message appears. If you fail to do this within the time limit, the system starts to run the extended BootWare segment. BASIC-BOOTWARE MENU(Ver 1.07 | Modify Serial Interface Parameter | | Update Extend BootWare | | Update Full BootWare | | Boot Extend BootWare | | Boot Backup Extend BootWare | | Reboot | Ctrl+U: Access BASIC-ASSISTANT MENU Enter your choice(0-5): Table 8 BASIC-BOOTWARE menu options Option Modify Serial Interface Parameter Update Extend BootWare Update Full BootWare Boot Extend BootWare Boot Backup Extend BootWare Reboot Ctrl+U: Access BASIC-ASSISTANT MENU Task Change the baudrate of the console port. Perform this task before downloading an image through the console port for software upgrade. Update the extended BootWare segment. If the corrupted extended segment has corrupted, choose this option to repair it. Update the entire BootWare, including the basic segment and the extended segment. Run the primary extended BootWare segment. Run the backup extended BootWare segment. Reboot the device. Press Ctrl + U to access the BASIC-ASSISTANT menu. Modifying serial port parameters When using the console port to access the system, make sure the port parameters are consistent with the serial port settings on the configuration terminal, including the baudrate, data bits, parity check, stop bits, flow control, and emulation. If the settings are inconsistent, communication will fail. With BootWare, you can change the baudrate. HP recommends that you change the default baudrate (9600 bps) to a higher baudrate for faster file transfer before downloading a system software image with XMODEM through the console port. To change the baudrate of the console port: 1. Enter 1 in the BASIC-BOOTWARE menu. Enter your choice(0-5): 1 BAUDRATE SET |Note:'*'indicates the current baudrate | | Change The HyperTerminal's Baudrate Accordingly | Baudrate Available 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
21
2.
Press
Ctrl + D
within four seconds after the "Press Ctrl+D to access BASIC BOOT MENU" prompt
message appears. If you fail to do this within the time limit, the system starts to run the extended
BootWare segment.
======================<BASIC-BOOTWARE MENU(Ver 1.07)>=======================
|<1> Modify Serial Interface Parameter
|
|<2> Update Extend BootWare
|
|<3> Update Full BootWare
|
|<4> Boot Extend BootWare
|
|<5> Boot Backup Extend BootWare
|
|<0> Reboot
|
============================================================================
Ctrl+U: Access BASIC-ASSISTANT MENU
Enter your choice(0-5):
Table 8 BASIC-BOOTWARE menu options
Option
Task
<1> Modify Serial Interface Parameter
Change the baudrate of the console port.
Perform this task before downloading an image through the
console port for software upgrade.
<2> Update Extend BootWare
Update the extended BootWare segment.
If the corrupted extended segment has corrupted, choose this
option to repair it.
<3> Update Full BootWare
Update the entire BootWare, including the basic segment
and the extended segment.
<4> Boot Extend BootWare
Run the primary extended BootWare segment.
<5> Boot Backup Extend BootWare
Run the backup extended BootWare segment.
<0> Reboot
Reboot the device.
Ctrl+U: Access BASIC-ASSISTANT MENU
Press
Ctrl + U
to access the BASIC-ASSISTANT menu.
Modifying serial port parameters
When using the console port to access the system, make sure the port parameters are consistent with the
serial port settings on the configuration terminal, including the baudrate, data bits, parity check, stop bits,
flow control, and emulation. If the settings are inconsistent, communication will fail.
With BootWare, you can change the baudrate. HP recommends that you change the default baudrate
(9600 bps) to a higher baudrate for faster file transfer before downloading a system software image with
XMODEM through the console port.
To change the baudrate of the console port:
1.
Enter
1
in the BASIC-BOOTWARE menu.
Enter your choice(0-5): 1
===============================<BAUDRATE SET>===============================
|Note:'*'indicates the current baudrate
|
|
Change The HyperTerminal's Baudrate Accordingly
|
|---------------------------<Baudrate Available>---------------------------|