HP 6400/8400 HP StorageWorks Enterprise Virtual Array Updating Product Softwar - Page 39

Verifying the installation on the management server, Upgrading the management module

Get HP 6400/8400 PDF manuals and user guides View all HP 6400/8400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Verifying the installation on the management server To verify that the software was installed successfully: 1. Ensure that the software icons for HP Command View EVA , HP Command View EVAPerf , and/or HP Storage System Scripting Utility appear on the desktop. 2. Run HP Command View EVA. 3. Verify the display of storage system resources in the interface. In the navigation pane, click Hardware and verify the following: • New, uninitialized arrays appear as uninitialized storage systems. • Previously initialized arrays appear with their previous names and correct status. (Select each storage array to view the Properties window.) • Previous disk groups, hosts, virtual disks, and other resources appear in the navigation pane. If information is not displayed properly, it may be necessary to configure your browser settings. See HP StorageWorks Command View EVA Installation Guide for more information. Upgrading the management module If you have an EVA4400, follow the procedures in this section to: • Upgrade HP Command View EVA on the management module (for array-based management) • Upgrade the management module software NOTE: Management module software is bundled with the array-based management version of HP Command View EVA. Thus, when you upgrade HP Command View EVA on the management module, you are also upgrading the management module software. Even if you are not using array-based management, you must complete the procedure in this section for the EVA4400 to ensure the management module software is current. Estimated time to complete: 25 minutes When to perform: Any time before the upgrade. To upgrade the management module: 1. Connect a server with a CD drive to the management module port (1, Figure 8) on the controller enclosure. Figure 8 Management module . 2. Insert the installation CD into the drive. HP StorageWorks Enterprise Virtual Array Updating Product Software Guide (XCS 09534000) 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Verifying the installation on the management server
To verify that the software was installed successfully:
1.
Ensure that the software icons for HP Command View EVA
, HP Command View EVAPerf
,
and/or HP Storage System Scripting Utility
appear on the desktop.
2.
Run HP Command View EVA.
3.
Verify the display of storage system resources in the interface. In the navigation pane, click
Hardware
and verify the following:
•
New, uninitialized arrays appear as uninitialized storage systems.
•
Previously initialized arrays appear with their previous names and correct status. (Select each
storage array to view the Properties window.)
•
Previous disk groups, hosts, virtual disks, and other resources appear in the navigation pane.
If information is not displayed properly, it may be necessary to configure your browser settings. See
HP StorageWorks Command View EVA Installation Guide
for more information.
Upgrading the management module
If you have an EVA4400, follow the procedures in this section to:
•
Upgrade HP Command View EVA on the management module (for array-based management)
•
Upgrade the management module software
NOTE:
Management module software is bundled with the array-based management version of HP Command
View EVA. Thus, when you upgrade HP Command View EVA on the management module, you are
also upgrading the management module software.
Even if you are not using array-based management, you must complete the procedure in this section
for the EVA4400 to ensure the management module software is current.
Estimated time to complete:
25 minutes
When to perform:
Any time before the upgrade.
To upgrade the management module:
1.
Connect a server with a CD drive to the management module port (1,
Figure 8
) on the controller
enclosure.
Figure 8 Management module
.
2.
Insert the installation CD into the drive.
HP StorageWorks Enterprise Virtual Array Updating Product Software Guide (XCS 09534000)
39