HP Engage Flex Pro-C G2 Maintenance and Service Guide - Page 37

Heat sink, Before removing the heat sink, follow these steps

Get HP Engage Flex Pro-C G2 PDF manuals and user guides View all HP Engage Flex Pro-C G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

2. To install a memory module, open both latches (1) of the memory module socket, and insert the memory module into the socket (2). Press the module down into the socket so that the module is fully inserted and properly seated. Be sure that the latches (3) are in the closed position. NOTE: A memory module can be installed in only one way. Match the notch on the module with the tab on the memory socket. The computer automatically recognizes the additional memory when you turn on the computer. Heat sink To remove the heat sink, use this procedure and illustration. Before removing the heat sink, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). 2. Remove the access panel (see Access panel on page 19). 3. Remove the fan and duct assembly (see Fan and duct assembly on page 28). Remove the heat sink: 1. Loosen the four Torx screws (1) that secure the heat sink to the system board. Heat sink 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
2.
To install a memory module, open both latches
(1)
of the memory module socket, and insert the
memory module into the socket
(2)
. Press the module down into the socket so that the module is
fully inserted and properly seated. Be sure that the latches
(3)
are in the closed position.
NOTE:
A memory module can be installed in only one way. Match the notch on the module with the
tab on the memory socket.
The computer automatically recognizes the additional memory when you turn on the computer.
Heat sink
To remove the heat sink, use this procedure and illustration.
Before removing the heat sink, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
2.
Remove the access panel (see
Access panel
on page
19
).
3.
Remove the fan and duct assembly (see
Fan and duct assembly
on page
28
).
Remove the heat sink:
1.
Loosen the four Torx screws
(1)
that secure the heat sink to the system board.
Heat sink
31