HP Engage Flex Pro-C G2 Maintenance and Service Guide - Page 45

Flex card, WLAN modules are designed with a notch to prevent incorrect insertion.

Get HP Engage Flex Pro-C G2 PDF manuals and user guides View all HP Engage Flex Pro-C G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

3. Disconnect the antenna cables (3) from the module. NOTE: The WLAN antenna cable labeled 1/AUX connects to the WLAN module AUX terminal. The WLAN antenna cable labeled 2/MAIN connects to the WLAN module MAIN terminal. 4. Pull the module (4) out of the socket. 5. If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve must be installed on the antenna connector, as shown in the following illustration. To install the WLAN module, reverse the removal procedure. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. Flex card To remove the flex card, use this procedure and illustration. Before removing the flex card, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). Flex card 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
3.
Disconnect the antenna cables
(3)
from the module.
NOTE:
The WLAN antenna cable labeled 1/AUX connects to the WLAN module AUX terminal. The
WLAN antenna cable labeled 2/MAIN connects to the WLAN module MAIN terminal.
4.
Pull the module
(4)
out of the socket.
5.
If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve
must be installed on the antenna connector, as shown in the following illustration.
To install the WLAN module, reverse the removal procedure.
NOTE:
WLAN modules are designed with a notch to prevent incorrect insertion.
Flex card
To remove the flex card, use this procedure and illustration.
Before removing the flex card, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
Flex card
39