HP Engage Flex Pro-C G2 Maintenance and Service Guide - Page 46

Rear expansion card

Get HP Engage Flex Pro-C G2 PDF manuals and user guides View all HP Engage Flex Pro-C G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

2. Remove the access panel (see Access panel on page 19). Remove the flex card: 1. Remove two Torx screws (1) that secure the card to the rear of the computer. 2. Lift the flex card (2) to disconnect it from the system board connector. To install the flex card, reverse the removal procedure. Rear expansion card To remove the rear expansion card, use this procedure and illustration. Before removing the rear expansion card, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). 2. Remove the access panel (see Access panel on page 19). 3. If installed, remove the serial port (see Powered serial ports on page 35). Remove the rear expansion card: 1. Remove the two Phillips screws (1) from the card. 40 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
2.
Remove the access panel (see
Access panel
on page
19
).
Remove the flex card:
1.
Remove two Torx screws
(1)
that secure the card to the rear of the computer.
2.
Lift the flex card
(2)
to disconnect it from the system board connector.
To install the flex card, reverse the removal procedure.
Rear expansion card
To remove the rear expansion card, use this procedure and illustration.
Before removing the rear expansion card, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
2.
Remove the access panel (see
Access panel
on page
19
).
3.
If installed, remove the serial port (see
Powered serial ports
on page
35
).
Remove the rear expansion card:
1.
Remove the two Phillips screws
(1)
from the card.
40
Chapter 4
Removal and replacement procedures