HP Engage Flex Pro-C G2 Maintenance and Service Guide - Page 40

Speaker, Rotate the drive cage to the upright position see

Get HP Engage Flex Pro-C G2 PDF manuals and user guides View all HP Engage Flex Pro-C G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

3. From the front of the computer, remove the Torx screw (3) from the front I/O assembly. 4. Pull the right side of the assembly (1) out slightly. 5. Slide the assembly (2) toward the right. 6. Pull the assembly and cables (3) out of the front of the computer. To install the front I/O assembly, reverse the removal procedure. Speaker To remove the speaker, use this procedure and illustration. Before removing the speaker, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 18). 2. Remove the access panel (see Access panel on page 19). 3. Rotate the drive cage to the upright position (see Hard drive on page 21). Remove the speaker: 1. Disconnect the speaker cable from the SPKR connector (1) on the system board. 34 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
3.
From the front of the computer, remove the Torx screw
(3)
from the front I/O assembly.
4.
Pull the right side of the assembly
(1)
out slightly.
5.
Slide the assembly
(2)
toward the right.
6.
Pull the assembly and cables
(3)
out of the front of the computer.
To install the front I/O assembly, reverse the removal procedure.
Speaker
To remove the speaker, use this procedure and illustration.
Before removing the speaker, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
18
).
2.
Remove the access panel (see
Access panel
on page
19
).
3.
Rotate the drive cage to the upright position (see
Hard drive
on page
21
).
Remove the speaker:
1.
Disconnect the speaker cable from the SPKR connector
(1)
on the system board.
34
Chapter 4
Removal and replacement procedures