HP Engage Flex Pro G2 Maintenance and Service Guide - Page 47

Front I/O assembly

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

6. When installing a solid-state drive, be sure thermal pads are installed on the bottom of the heat sink (1) and the inside of the bracket (2). To install the solid-state drive, reverse the removal procedure. Front I/O assembly To remove the front I/O assembly, use these procedures and illustrations. Before removing the front I/O assembly, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 21). 3. Remove the optical drive (see Optical drive on page 23). 4. Remove the front bezel (see Front bezel on page 23). 5. Rotate the drive cage to the upright position (see Rotating the drive cage on page 26). Remove the front I/O assembly: 40 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
6.
When installing a solid-state drive, be sure thermal pads are installed on the bottom of the heat sink
(1)
and the inside of the bracket
(2)
.
To install the solid-state drive, reverse the removal procedure.
Front I/O assembly
To remove the front I/O assembly, use these procedures and illustrations.
Before removing the front I/O assembly, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
21
).
3.
Remove the optical drive (see
Optical drive
on page
23
).
4.
Remove the front bezel (see
Front bezel
on page
23
).
5.
Rotate the drive cage to the upright position (see
Rotating the drive cage
on page
26
).
Remove the front I/O assembly:
40
Chapter 4
Removal and replacement procedures