HP Engage Flex Pro G2 Maintenance and Service Guide - Page 48

Slide the assembly, out slightly.

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

1. Remove one Torx screw (1) from the front grill, and then rotate the grill (2) from right to left and off the front of the computer. 2. Disconnect the cable from the PB/LED connector (1) on system board. 3. Disconnect the cable from the FRONT USB3 connector (2) on system board. 4. From the front of the computer, remove the Torx screw (3) from the front I/O assembly. 5. Rotate the right side of the assembly (1) out slightly. 6. Slide the assembly (2) toward the right. 7. Rotate the left side of the assembly (3) approximately 90° so the assembly is perpendicular to the front of the computer. Front I/O assembly 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
1.
Remove one Torx screw
(1)
from the front grill, and then rotate the grill
(2)
from right to left and off
the front of the computer.
2.
Disconnect the cable from the PB/LED connector
(1)
on system board.
3.
Disconnect the cable from the FRONT USB3 connector
(2)
on system board.
4.
From the front of the computer, remove the Torx screw
(3)
from the front I/O assembly.
5.
Rotate the right side of the assembly
(1)
out slightly.
6.
Slide the assembly
(2)
toward the right.
7.
Rotate the left side of the assembly
(3)
approximately 90° so the assembly is perpendicular to the
front of the computer.
Front I/O assembly
41