HP Engage Flex Pro G2 Maintenance and Service Guide - Page 61

WLAN antennas and external connectors

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

1. Remove the two Phillips screws (1) from the port. 2. Lift the port (2) up to disconnect it from the connector on the system board. To install the rear expansion port, reverse this procedure. WLAN antennas and external connectors To remove the WLAN antennas and external connectors, use this procedure and illustration. Before removing the WLAN antennas and external connectors, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 21). 3. Rotate the power supply to the upright position (see Rotating the power supply on page 44). Remove the WLAN antennas and external connectors: 1. Lift the retainer latch (1) on the back of the computer. 2. Lift the antenna connector assembly (2) up and out of the slot. 3. Disconnect the antenna cables (3) from the WLAN module. 4. Remove the antenna cables from the clip (4) on the back of the computer. 54 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
1.
Remove the two Phillips screws
(1)
from the port.
2.
Lift the port
(2)
up to disconnect it from the connector on the system board.
To install the rear expansion port, reverse this procedure.
WLAN antennas and external connectors
To remove the WLAN antennas and external connectors, use this procedure and illustration.
Before removing the WLAN antennas and external connectors, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
21
).
3.
Rotate the power supply to the upright position (see
Rotating the power supply
on page
44
).
Remove the WLAN antennas and external connectors:
1.
Lift the retainer latch
(1)
on the back of the computer.
2.
Lift the antenna connector assembly
(2)
up and out of the slot.
3.
Disconnect the antenna cables
(3)
from the WLAN module.
4.
Remove the antenna cables from the clip
(4)
on the back of the computer.
54
Chapter 4
Removal and replacement procedures