HP Engage Flex Pro G2 Maintenance and Service Guide - Page 60

Serial port, Rear expansion port, To install the serial port, reverse the removal procedure.

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

To install the audio board, reverse the removal procedure. Serial port To remove the serial port, use this procedure and illustration. Before removing the serial port, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 21). Remove the serial port: NOTE: You can install different rear expansion ports into this location. While the installation process is similar, the system board connector might differ. 1. Remove the two Torx screws (1) that secure the serial port to the rear of the computer. 2. Disconnect the serial port cable from the system board connector labeled COMA (2). 3. Remove the serial port and cable (3) from the computer. To install the serial port, reverse the removal procedure. Rear expansion port To remove the rear expansion port, use this procedure and illustration. Before removing the rear expansion port, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 21). 3. If installed, remove the serial port (see Serial port on page 53). Remove the rear expansion port: Serial port 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
To install the audio board, reverse the removal procedure.
Serial port
To remove the serial port, use this procedure and illustration.
Before removing the serial port, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
21
).
Remove the serial port:
NOTE:
You can install different rear expansion ports into this location. While the installation process is
similar, the system board connector might differ.
1.
Remove the two Torx screws
(1)
that secure the serial port to the rear of the computer.
2.
Disconnect the serial port cable from the system board connector labeled COMA
(2)
.
3.
Remove the serial port and cable
(3)
from the computer.
To install the serial port, reverse the removal procedure.
Rear expansion port
To remove the rear expansion port, use this procedure and illustration.
Before removing the rear expansion port, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
21
).
3.
If installed, remove the serial port (see
Serial port
on page
53
).
Remove the rear expansion port:
Serial port
53