HP Engage Flex Pro G2 Maintenance and Service Guide - Page 53

Hard drive

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

5. If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve must be installed on the antenna connector, as shown in the following illustration. To install the WLAN module, reverse the removal procedure. NOTE: WLAN modules are designed with a notch to prevent incorrect insertion. Hard drive To remove a hard drive, use these procedures and illustrations. You can install a 5.25 inch hard drive into a bay on the floor of the computer chassis or into the drive cage under the optical drive. Before removing the hard drive, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 20). 2. Remove the access panel (see Access panel on page 21). 3. Remove the optical drive (see Optical drive on page 23). Remove the primary hard drive: 1. Rotate the drive cage to the upright position (see Rotating the drive cage on page 26). 2. Rotate the power supply to the upright position (see Rotating the power supply on page 44). 3. Disconnect the power and data cables (1) from the back of the drive. 4. Press the release button (2), slide the drive toward front of the computer and pull it up and out of the computer (3). 46 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
5.
If the WLAN antenna is not connected to the terminal on the WLAN module, a protective sleeve
must be installed on the antenna connector, as shown in the following illustration.
To install the WLAN module, reverse the removal procedure.
NOTE:
WLAN modules are designed with a notch to prevent incorrect insertion.
Hard drive
To remove a hard drive, use these procedures and illustrations. You can install a 5.25 inch hard drive into
a bay on the floor of the computer chassis or into the drive cage under the optical drive.
Before removing the hard drive, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
20
).
2.
Remove the access panel (see
Access panel
on page
21
).
3.
Remove the optical drive (see
Optical drive
on page
23
).
Remove the primary hard drive:
1.
Rotate the drive cage to the upright position (see
Rotating the drive cage
on page
26
).
2.
Rotate the power supply to the upright position (see
Rotating the power supply
on page
44
).
3.
Disconnect the power and data cables
(1)
from the back of the drive.
4.
Press the release button
(2)
, slide the drive toward front of the computer and pull it up and out of the
computer
(3)
.
46
Chapter 4
Removal and replacement procedures