HP Engage Flex Pro G2 Maintenance and Service Guide - Page 65

Update the SMBIOS information in Computer Setup., When replacing the system board

Get HP Engage Flex Pro G2 PDF manuals and user guides View all HP Engage Flex Pro G2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

2. Remove the eight Torx screws (1) from the board. 3. Slide the system board (2) toward the front of the computer enough to remove the connectors from the back of computer, and then lift the system board (3) out of the computer. To install the system board, reverse the removal procedure. NOTE: When replacing the system board, you must change the chassis serial number in the BIOS. When replacing the system board, you must reprogram the SMBIOS information about the affected computer. Failure to reprogram the board will result in eventual failure, such as an activation failure (when you would have to reactivate the computer) or a system recovery failure. Update the SMBIOS information in Computer Setup. 58 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
2.
Remove the eight Torx screws
(1)
from the board.
3.
Slide the system board
(2)
toward the front of the computer enough to remove the connectors from
the back of computer, and then lift the system board
(3)
out of the computer.
To install the system board, reverse the removal procedure.
NOTE:
When replacing the system board, you must change the chassis serial number in the BIOS.
When replacing the system board, you must reprogram the SMBIOS information about the affected
computer. Failure to reprogram the board will result in eventual failure, such as an activation failure
(when you would have to reactivate the computer) or a system recovery failure.
Update the SMBIOS information in Computer Setup.
58
Chapter 4
Removal and replacement procedures