HP Engage Go 10 Maintenance and Service Guide - Page 33

Touch board, Hub board

Get HP Engage Go 10 PDF manuals and user guides View all HP Engage Go 10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Touch board To remove the touch board, use this procedure and illustration. Before removing the touch board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Disconnect the battery cable from the system board (see Battery on page 23). Remove the touch board: ▲ Use a flat tool (1) to release the board out from the computer (2). The board is secured with adhesive. To install the touch board, reverse the removal procedure. Hub board To remove the hub board, use this procedure and illustration. Before removing the hub board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Disconnect the battery cable from the system board (see Battery on page 23). Remove the hub board: 1. Disconnect the cable from the ZIF connector on the left side of the board (1). 2. Disconnect the cable from the reverse ZIF connector on the right side of the board (2). 3. Disconnect the lower cable, located under the top cable, on the right side of the board (3). 4. Remove the two Phillips screws from the board (4). Touch board 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Touch board
To remove the touch board, use this procedure and illustration.
Before removing the touch board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
23
).
Remove the touch board:
▲
Use a flat tool
(1)
to release the board out from the computer
(2)
. The board is secured with adhesive.
To install the touch board, reverse the removal procedure.
Hub board
To remove the hub board, use this procedure and illustration.
Before removing the hub board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
23
).
Remove the hub board:
1.
Disconnect the cable from the ZIF connector on the left side of the board
(1)
.
2.
Disconnect the cable from the reverse ZIF connector on the right side of the board
(2)
.
3.
Disconnect the lower cable, located under the top cable, on the right side of the board
(3)
.
4.
Remove the two Phillips screws from the board
(4)
.
Touch board
25