HP Engage Go 10 Maintenance and Service Guide - Page 42

System board

Get HP Engage Go 10 PDF manuals and user guides View all HP Engage Go 10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

3. Remove the board from the computer (3). To install the power button board, reverse the removal procedure. System board To remove the system board, use this procedure and illustration. NOTE: All system board spare part kits include replacement thermal material. Before removing the system board, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Remove the battery (see Battery on page 23). 4. Remove the solid-state drive (see Solid-state drive on page 24). 5. Remove the WWAN module (see WWAN module on page 28). Remove the system board: 1. Disconnect the following cables from the system board: (1) WLAN antennas cables (2) Ambient light sensor cable (3) Rear camera cable (4) Front camera cable (5) Camera LED cable 34 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
3.
Remove the board from the computer
(3)
.
To install the power button board, reverse the removal procedure.
System board
To remove the system board, use this procedure and illustration.
NOTE:
All system board spare part kits include replacement thermal material.
Before removing the system board, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Remove the battery (see
Battery
on page
23
).
4.
Remove the solid-state drive (see
Solid-state drive
on page
24
).
5.
Remove the WWAN module (see
WWAN module
on page
28
).
Remove the system board:
1.
Disconnect the following cables from the system board:
(1)
WLAN antennas cables
(2)
Ambient light sensor cable
(3)
Rear camera cable
(4)
Front camera cable
(5)
Camera LED cable
34
Chapter 4
Removal and replacement procedures