HP Engage Go 10 Maintenance and Service Guide - Page 45

Bump cover and pogo connector

Get HP Engage Go 10 PDF manuals and user guides View all HP Engage Go 10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

4. Remove the WWAN module (see WWAN module on page 28). 5. Remove the system board (see System board on page 34). Remove the NFC module: ▲ Peel the NFC module, cable, and antenna off the inside of the computer. These components are secured with adhesive. To install the NFC module, reverse the removal procedure. Bump cover and pogo connector To remove the bump cover and pogo connector, use this procedure and illustration. Before removing the bump cover and pogo connector, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Disconnect the battery cable from the system board (see Battery on page 23). Remove the bump cover: 1. Remove the barcode scanner doors (1), and then remove the two Phillips screws from under the doors (2). Bump cover and pogo connector 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
4.
Remove the WWAN module (see
WWAN module
on page
28
).
5.
Remove the system board (see
System board
on page
34
).
Remove the NFC module:
▲
Peel the NFC module, cable, and antenna off the inside of the computer. These components are secured
with adhesive.
To install the NFC module, reverse the removal procedure.
Bump cover and pogo connector
To remove the bump cover and pogo connector, use this procedure and illustration.
Before removing the bump cover and pogo connector, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
23
).
Remove the bump cover:
1.
Remove the barcode scanner doors
(1)
, and then remove the two Phillips screws from under the doors
(2)
.
Bump cover and pogo connector
37